EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Wondom Adau1701 bluetooth not working anymore after writing on the DSP
Hello everyone, after writing on my DSP's memory, the Bluetooth no longer works, I can connect and play music but there is no sound. The Bluetooth worked before I write on the DSP.The Jack 3.5 entry w
-
EVAL-ADAU1701MINIZ – High Crystal Drive Level
EVAL-ADAU1701MINIZ – High Crystal Drive Level Hello all, I’ve read some posts regarding the ADAU1701 Crystal start-up issues, so I have made some measurements based on the ADAU1701 Evaluation module (
-
ADAU1466 Synchronous Sample Rate Conversion (48kHz to 96kHz) the Hard Way
Let's say I have an I2S source (ADC) at 48kHz and I want to run my ADAU1466 DSP filters at 96kHz and I want the output I2S serial port (DAC) to run at the same 96kHz. The MCLK is synchronous to the AD
-
Applying dynamic EQ filtering based on signal amplitude
Hi! I'm working on a project with some small size PA speakers that are intended to be used mostly for live speech (e.g. conferences) I would like to experiment with the idea of applying dynamic filter
-
Ext Slew Volume Control (HW Slew)
Dear Team. I am analyzing the Ext Slew Volume Control block and have the following queries 1. How are the values measured? What is the tool/procedure used to arrive at these values that have been cons
-
EVAL-ADAU1467Z schematic example about AD1937
Dear all, I am using the EVAL-ADAU1467Z to check the operation. I am going to create a schematic that inputs to IN1 (ch32-33) and outputs it to Out1 (ch0-1). I wrote schematic, but I am not familiar w
-
ADAU1466: Best way to brickwall filter before decimation?
I have a use case where the incoming sample rate (i.e. 384kHz) is too high for my processing, so I'm decimating by a factor of 2. In future, I'm seeing even more multirate filtering demands, so I'm cu
-
Upsampling Block - LPF characteristics?
The upsampling block (available for ADAU145x) has a check box for an LPF. There is no documentation for this filter. Is it FIR? IIR? What are the cutoff characterisitics?
-
A commom audio transfer question in TDM16 format
Hi, I always meet with difficulty in several different projects. When I use TDM16 format to receive datas using ADAU1452, I can get all the 16 channels audio datas and it sounds like good. What confus
-
ADAU1761 - RMS Table RMS TC and Decay do not correspond when set to the same rate
I expect the output graph to look like the one at the bottom in the image, however, the result is asymmetrical like in the top graph in the image. Am I understanding the RMS Table settings incorrectly
-
ADAU1979: What starts a conversion cycle?
We're using multiple ADAU1979 ADC's in our design. The datasheet for this ADC is notably vague on which clocks are controlling the internal conversion. It is understood that the LRCLK and BCLK control
-
''Discrete'' RMS Table block for specific needs/settings (IEC 61672 fast and slow time weighting)
Hi All, I need the functionality of the RMS table block (Level Detectors/Lookup Tables > RMS Table > Range (-93 to +3 dB) > RMS Table), but for my application the available dB/s range and precision is
-
Support for the SSM2604 codec in SigmaStudio? Or recommended replacement that is already supported?
Are there plans, or would it be possible to request, for SigmaStudio to get support for the SSM2604 audio codec? I am considering upgrading the DSP I am using for the next revision of my development b
-
Is it possible to store runtime parameters on self-boot EEPROM?
Hi I've asked several questions, none of which have had any replies, so maybe I'm asking for the wrong thing. I'm using an ADAU1467 with an SPI EEPROM for self-boot, and I want various runtime paramet
-
ADAU1467 Stop/Start clocks during boot
Our system uses an ADAU1467 at its core. Several I2C peripherals are initialized by the ADAU1467 during the startup sequence. We'd like to prevent the BCLK and LRCLK signals from starting up before we
-
[Bug Report] ADAU1467 Interface Write creates Self Boot failure
Hi Having spent many hours trying to understand what was going wrong, I now have a minimum project to demonstrate this failure. Simply put, the existence of an Interface Write block prevents Self Boot
-
ADAU1787 Phase vs Frequency specification
Hi Sir, Can you help to check either ADAU1787 can provide phase vs frequency specification , just like ADAU1777 datasheet figure 11 , figure 14? Thanks for your help.
-
[BUG REPORT] After dragging and dropping a node onto the schematic, clicking anywhere before waiting for a few moments adds duplicate nodes
I'm using SigmaStudio 4.6 and have noticed a consistent issue that occurs when dragging and dropping nodes from the ToolBox onto the schematic. After dropping the new node onto my schematic, if I clic
-
How do I recognize an ADAU1452-150?
I'm looking to buy a cheap Aliexpress/eBay ADAU1452 board to learn more about the Analog family of DSPs. As usual, browsing the seller's description, there is some weirdness that hopefully can be expl
-
Can custom SigmaStudio communication plugins be created?
My project has an ADAU1701 and an STM32 microcontroller with USB device support. At the moment, I am using an USBi module to connect SigmaStudio to my board's I2C bus via exposed header pins, which do
-
ADAU1452+2xAD1933 multichannel output
Good day. I needed to get 16 channels of audio output from one source. I plan to use ADAU1452 and two AD1933 chips for this. In the datasheet on ADAU1452 I found a "Flexible TDM Otput" section. Can yo
-
ADAU1451 Multirate processing and clocks/start pulse/sampling rate settings problem
Hi, I’m having some troubles with multirate processing on the ADAU1451 (scheme below). I want to receive : 1) audio data at 48 kHz 2) have a first stage of processing at 48 kHz 3) then upsample the au
-
Frequency response of the fractional delay component
Hello I observe the frequency response of the fractional delay line in the ADAU1787 as a function of it's configured delay. The project and spectrum screens are attached. The blue line: the spectrum a
-
I design a Theremin with 4 Channel Amplifier how i use the input in this Project until the Theremin works.
Hi Community, i don't know, how can man use the SigmaStudio Input on the Beocreate 4 Channel Amplifier Pin. I want to design a simple Theremin. Please cann you help me? Sorry for my Englisch Thanks yo
-
ADAU1467 Eeprom Interface Write problem
I'm using an ADAU1467 with self-boot eeprom. Writing to the eeprom via the DSP works no problem, using the same settings as the EVAL board. However, I'm using a Rotary Encoder for volume, and I want i