EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1452 clock generator 3 to generate DSP system clock
Hi I would like clarification on whether the the clock generator 3, sourced in my application from an external I2S LR clock (44.1k/48k/96k probably not 192k), can be used to generate the overall syste
-
Problems with EVAL-ADAU1452RevBZ in TDM mode
Hi, I'm trying to develop a multi-canal system with ADAU1452 in TDM16 mode that communicates to ADAU1966A in Standalone Mode (TDM16, Slave serial audio interface and 256 × Fs ). I control the DS
-
Input sampling rate change signal
Hello! I am new to sigmastudio design and I need some help. In my project I need to provide an external signal to the control MCU that signals a change in the input sampling rate at the SPDIF input. D
-
ADAU 1466 Data Sheet
Where do I find the other end of the 2 connectors in the attachments of the ADAU1466 Data Sheet ? Dose ADAU1452 pins the same as ADAU1466 , and are these 2 chips interchangeable ? Thanks in advance Ed
-
Accessing ADC of ADAU1701
I need to use an ADAU1701, namely its ADC and DAC. I have to produce some signal using DAC and store some another signal using ADC. Thereby, received samples with ADC have to be saved somewhere for fu
-
i2s adau1701
hello everyone! i'm using a custom board with the adau 1701 on selfboot mode i'm trying to figure out how to send and receive audio from the adau to the stm32f401re evaluation board i was looking at d
-
Measuring a frequency response
My task is to measure a frequency responcse of a LTI system. I have an ADAU1701 and a microcontroller at my disposal. I have already solved the case when a sweep-generator used for measuring but I als
-
SigmaDSP ADAU1466 pink noise generator
Hi. Expert. I'm checking the pink noise generator of SigmaDSP ADAU1466 and it's weird. Please help. I tested the ADAU1466 noise generator and the Audio Precision output. CH1_3: Audio Precision output
-
EVAL-ADAU1467 passing signal on OUT1, but not on OUT2, OUT3 and OUT4
I have searched for this issue and have not been able to find the answer. It's probably something painfully obvious, but I can't figure it out! With the basic program recommended by the guide, I am ab
-
Allow aliasing in AUX ADC (1451/1452)?
I'm using an ADAU1452 at 192kHz sample rate for a project. I'm aware the auxiliary ADC's run at 48kHz regardless of the DSP sample rate. If I try to use these to measure signals up to 96kHz, will this
-
ADAU1466 second page addressing
Hi all, We are implementing the interface for controlling an ADAU1466 from an MCU and we've found that the second page addressing is quite inconvenient. This is because the addresses of parameters tha
-
Two ADAU1452 in same config, clock issues_
Hi, I would like to process 6 channels of audio, and the ADAU1452 I own, have 4 inputs each (I have two). Can I use them simultaneously like: -. Channel 1, 2, 3 and 4 to DSP A -. Channel 5, 6, 7 and 8
-
Eval-ADAU1467 - no analog output on OUT2(ch 4-5)
Hello, I have been playing around with the ADAU1467 eval board (EVAL-ADAU1467 Rev. B) and am not seeing an output on OUT2, but I am seeing an output on OUT1 channels. I imagine this is probably an inc
-
Aux ADC controlled mux
Hi all, the attached file is a project for an frequency generator with i2s output, to test i2s dac's. The frequencies should be fixed values e.g. 10, 20, 50, 100... Hz and the signal -90, -80, -70db .
-
How do I transfer PEQ parameters in Sigma Studio
I have a parametric EQ block in one project with a number of lines of filters in it. I want to copy this set of filters from one project to another. How can I do this. I have tried this method: In Pro
-
EVAL-ADUSB2EBZ
My glorious EVAL-ADUSB2EBZ suddenly stopped working. The U8 ADP1711AUJZ-3.3-R7 voltage regulator heats up. I cut track OUT pin 5 and the regulator works, I measure 3.3 volts on free pin 5. Unfortunate
-
Beam Forming Designer with EVAL-ADAU1467Z
Hello. I want to try to use Beam Forming Designer with EVAL-ADAU1467Z. I looked for the information about the block, and there were several wiki pages about beam forming like this: https://ez.analog.c
-
ADAU1452 sampling frequency
Hi, I use an ADAU1452 to EQ a few subwoofers, and noticed the filters were not working properly (ie. PEQ was not affecting the signal in any way!) I realized I was setting the sample rate only in samp
-
Adau 1701 hold parameter
Hello everyone. It's my first time here, i'm using a custom board with the adau 1701 and eeprom, self boot mode. I'm trying to use 1 single potentiometer connected to the aux adc and 2/3 buttons to se
-
ADAU1466 PINK NOISE GENERATOR
Hello. I used ADAU1466 + SIGMASTUDIO 4.2 to create PINK NOISE GENERATOR as shown in the image below. However, it operates slightly differently from PINK NOISE output from other devices. In the image b
-
adau1466 pll max frequency
Dear all, I'm not able to reach core max frequency with my adau1466. Xtal = 12.288 predivider = 4 pll mult = 80 12.288/4*80 = 245.76 MHz If i try to run faster, the pll locks and unlocks few seconds l
-
Analog ASRC and ADAU1701
HI, this is my first DSP project (a three-way audio crossover, with speaker compensation). I already have a Sure ADAU1701 board, with relevant programmer. I would like to add a SPDIF input, with multi
-
fft on adau1452
I would like to use the FFT function on the adau1452 (using SigmaDSP tools) to output spectrum analysis via i2c. 1. is this possible? 2. how can i view the FFT response using my EVAL-ADAU1452? Thanks!
-
spdif connector
Can I use RCA jack for the spdif connectors ? Thanks in advance .
-
ADAU1467 SPI clock Selfboot
Hi ADAU1467 works as SPI master when selfboot is enabled, but how to configure SPI clock frequency for the SPI master? I tried to look through 1467 datasheet and past EZ threads, but couldn't find it.