EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Loading exported SigmaStudio 4.5 image into ADAU1761 from BF706
Hi - Has anyone successfully loaded an exported SigmaStudio image into an ADAU1761 CODEC from a BF706 using Analog Devices provided code adi_adau1761_SigmaStudioLoad() in adi_adau1761.c.? I'm able to
-
Devboard and DSP library pricing, availability
Hi! For a new audio project I am considering the SigmaDSP suite and related products. Currently I need some help answering these questions: - Where can I get dev boards and prices / shipping times? -
-
Adau1701 bluetooth i2s
I'm developing an amplifier board, and i want to stream stereo sound to the adau1701 via a Bluetooth module (nrf52832). i want the DSP to work as a master since I already have a crystal connected to i
-
Input generate high volume white noise on adau1701 board
Hello! I am so far a beginner in DSP designs and currently in the process of designing a DSP board. However, I have come across a strange noise problem as following: I have an ADAU1701 board whit a mo
-
Noise on ADAU1701
Hello Experts I have a noise issue on ADAU1701 Above is the old board layout, after reading this forum and seeing stuff about layout causing noise. I have revised the layout to below, the layout follo
-
EVAL-Adau1787Z design error?
I was trying to use connectors J6 or J7 to connect to the digital microphone inputs on the ADAU1787 eval board. After having no success, I eventually connected the microphone to J5 which worked for me
-
SigmaStudio FFT Equalization
Hello! is there such an opportunity to repeat a complex equalizer frequency response curve with sigmastudio? I spent a very long time adjusting the equalization to the ears of my monitors and headphon
-
REAL programming of EEPROM through DSP in a production test environment
I've seen several posts that dance around the issue, but none seem to really get to the point. Is there a scriptable (command line preferred) tool that can write a SigmaStudio DSP image through the DS
-
Signal Detection for Power Amp Standby
Hi, I wrote this post as a question, but then discovered the Signal Detect block already works exactly as I had wanted! So I am instead posting this to help others who might think the same as me. I am
-
ADAU1777 SINC Filter Characteristics?
ADI, We are using the ADAU1777 CODEC for our audio implementation program. We have enabled the 4th Order Filter registers as seen below: These are registers 0x1B and 0x1C set to 0x00. We have plotted
-
Preload value of IIR filter?
I'm working on making thermal models of speaker drivers to guard these from overheating, and predict before they overheat. I made a model for the power delivered to the driver and are modelling voice-
-
ADAU1701 GPIO Configuration
Hello, I am working on implementing the ADAU1701 into a headphone design but I am unclear about which pins to use for I2S on the 1701. The proposed I2S signal flow is: BT Receiver -> ADAU1701 -> Exter
-
Leaving the USBi Interface connected without PC connected
What do I have to do to let the USBi Interface being connected to the 1467 ( or 1452 ) via master control port WITHOUT having a PC (Sigmastudio) connected to the USBi when powering the board on ( self
-
i2s converters to go with adau 1701 / 1401
Hi, as there are 8 i/o s on the adau 1701 / 1401 I am wondering what kind of converters I could use for that and how to set them up. Not sure if this is possible or advisable but as I2C control is wor
-
diffedifference between 24mhz&12mhz
hello adi engineer, I reviewed answers in this forum which introduce methods to set 24.576mhz for the adau1701 with 512fs PLL. meanly the fs is 48khz as well. may I ask the differences between 12.288M
-
Set different FS for FastDSP and SigmaDSP when compile
Hi All, I use SigmaDSP of ADAU1787 to run algorithm and it works well. I set the FS is 48KHz in the toolbar. When I want to use FastDSP to run ANC and I need to set a higher FS(192KHz). I click link c
-
occasional audio noise when powering up ADAU1467
I have downloaded a huge program to the ADAU1467 and during selfboot occasionally I get a short loud audio noise when powering up the ADAU1467. Can someone give me a simple advice what to do in the si
-
SigmaStudio NxM maximum input, output
Good Morning, I am looking at making a routing switchboard out of the ADAU145x using the NXM mixer algorithm, however while the ADAU145x has 48x48 inputs to outputs the largest mixer block I can creat
-
Upload hex code to DSP from MCU
Where can I find any appnote, how to upload firmware in HEX to DSP (ADAU1466) with MCU over SPI? Is it possible?
-
ADAU1451 ASRC_MUTE strange behaviour
Dear All, When ASRC do not have any valid input signal (no clock at input, ASRC unlocked) it should go to mute and output a data of 0 no ? Instead ASRC outputs a continuous data value. When ASRC is lo
-
Data Soft Clip module ADAU 1466 & 1467
Hello, friends! I am developing guitar amplifiers based on ADAU 1466 & 1467. There is a problem using clipping in the Data Soft Clip module, it has a very small clipping adjustment range. There is no
-
Daisy Chain CODEC's into DSP
I have a customer that is looking to utilize an ADSP-2156x DSP to take analog inputs, perform some DSP functions, then output analog signals. Both the inputs and outputs will be a mix of mono and ster
-
LabVIEW source code to read AD7402
Hi, Can anyone help me with the LabVIEW FPGA source code to the AD7402 ADC. I tried to develop it myself without success. ad7402 adc Integrated/Special Purpose A/D Converters delta-sigma Isolated A/D
-
Sync SPDIF Tx rate to SPDIF Rx rate
Hi I similar question was on a post of the same "Subject" name https://ez.analog.com/dsp/sigmadsp/f/q-a/65396/sync-spdif-tx-rate-to-spdif-rx-rate Using the ADAU1452. The DSP is Locked to an external I
-
ADAU1467 I2S input slave mode
Hi everybody. I am trying to connect our ADAU1467 based mainboard with our wireless audio receiver board based on Texas Instruments CC8531. As the CC8531 in receiver mode can only be set to clock mast