EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Use ADAU1702 SigmaDSP to do Virtual Surround
Hi All I want Use ADAU1702 SigmaDSP to develop about Virtual Surround headphones Sound Box Use USB connect computer the other end connect headphone How can I do? ADI have any refrence code about Virtu
-
ADAU1466 digital microphone connection setup
For our new design I need to use 4 PDM microphones with ADAU1466WBCPZ300 DSP. Unfortunately, I can’t get any signal from mics on the OUT1 (I2S). In my initial project all 4 mics mixed in to one left c
-
Register compatibility ADAU1452 <> ADAU1462 ?!
Though it is said the two mentioned parts are 100% SW and register compatible their spec says something different: Is the ADAU1462 spec correct? Thanks Audio Signal Processors adau1452 SigmaDSP Audio
-
ADAU1466 IIRDF2_2nd order filter design precision issue(values are overflow)
Hi team, I am new to sigmastudio, In ADAU1466(fixed point arth.) Dsp processor i am designing Parameter EQ filter, in that iirdf2_2nd order filter using, in filter states are over flows values due to
-
How to handle non-standard TDM protocol?
Hello, I am looking for an audio DSP that can handle a non fully standard TDM protocol. It is like a 16 bits 8 bidirectional channel TDM8 but instead of using 32 bits per audio channel on the DATA lin
-
Adau1701 soundbar
Hello, I would like to realize a soundbar with SigmaDSP Processors Adau1701 as you can see in this schematic The Adau1701 will be used to create surround up to 5.1 with filter. But I'm new in DSP and
-
ADAU1452 based custom board, unable to read registers
Hello everyone, I designed a PCB based on the ADAU1452 DSP, where the relevant parts in terms of my question are basically copy-pasted from the EVAL board of this DSP. Only the layout is different. Wh
-
Best way to switch between two dynamic processor profiles
Hello, I want to switch between two profiles created using a dynamic processor, as if to do an A/B test. I can use a uC and do an I2C WRITE but I was wondering if the uC can be avoided. Ideally I woul
-
Switching with audio
Hi, Is there a way to switch between two signals using the input signal? I would like to feed a clock signal into the audio input and use this to swith inside sigma studio between signal paths (ie rou
-
ADAU1701 - Reset pin required for the USBi control interface board?
Hello all, The EVAL-ADAU1701MINIZ schematic shows that the DSP reset pin should be connected to the USBi interface board. I've probed the reset trace (using a scope with falling edge trigger) and noti
-
ADAU1466 and Arduino communication
Hi, I'm trying to make my ADAU1466 eval board to communicate with my Arduino ATMEGA2560. I'm using Arduinos code "i2c_scanner" that should be able to scan and detect the I2C addresses for slave device
-
ABC Testing with Momentary Switches
Using SigmaStudio 4.5 and ADAU1452 DSP. I am trying to setup an ABC test with one input and 3 outputs. I have a board with 3 momentary switches connected to 3 AUX ADC inputs. I'm using ADC inputs now
-
Digital volume control Adau1452
Hello. Recently I found great topic with digital volume control that may help with resolution decreasing in low volume values KJBob gave interesting algorithm for that in the topic here https://ez.ana
-
ADAU1467 MCLK routing
Hi, I have 1 x ADAU1467 running using I2C from micro. all of its ports are hooked up to hardware. I have an 12.288mhz oscillator with 8 channel buffer driving XTALIN/MCLK pin on ADAU1467 and other har
-
DSP MCU communication
How can i get an ADAU1466Z and Arduino ATMEGA2560 to communication through I2C in Arduino IDE? i connect SDA and SCL to the ADAU1466Z, but i dont understand anything from here.
-
ADAU1787 Sigmastudio4.5 How to export filter coefficients in NLMS?
Thank you ADAU1787 Integrated/Special Purpose A/D Converters Audio CODECs
-
Need help to put DSP in SPI mode, using microcontroller.
Hi Im trying to put ADA1401 in SPI mode, but without success, so i will need some help. First, i do not have an oficial board, i have cheaper chinese one, and this board missing pin header for ADDR1/C
-
Hmc833 控制字
能否帮我发一个hmc833 的参考控制字?
-
ADAU-1467 Slew and Distortion - updating parameters
Hi, I have implemented 5 band filter (based on Double Precision, Text-In (unlinked) SW Skew) with Biquad coeffs calculated on Host CPU. I have a 50uS delay after each Param write. GOAL: Any update to
-
Sigmastudio
Dear ADI team, i am working on ADAU1467 for i2s to TDM convertor. i need user guide / video/ application notes for Sigma studio to create first application. i have downloaded software. but need quidan
-
ADAU1401 register readback
Hi, I want to read a value using the readback function in SigmaStudio using a microcontroller connected to the I2C bus. For testing purpose I have connected a DC value to the readback module. When I p
-
Eval-ADAU1467 dimensions
Just a quickie - I've ordered an EVAL-ADAU1467 and would like to get an enclosure ready for it when it lands - does anyone know the board dimensions please? I can't see them in the user guide. Thanks.
-
USB communication errors ADAU1701
Hi just invested in some Sure boards AMP2 and ICP3 and i seem to be getting ye old communication errors no matter what i try .. I have looked around the forum for a good list of things to try so i gue
-
What is the "power-down" state of the ADAU145x?
For standby (soft powerdown) operation we need to of course draw minimal power, and I'd like to avoid switching the IOVDD off, mostly because voltages on the potentially still-active I2C bus can destr
-
ADAU1467: share clock in SDATAIN and SDOUT?
Hi, I have an external I2S device, which shares the same clock (I2S_BCLK and I2S_LRCLK) for both I2S_TXD and I2S_RXD. I plan to connect I2S_TXD to SDATA_IN0 and I2S_RXD to SDATA_OUT2 (the port number