EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
the right solution for my this audio project
hi Forum, I'm an hardware designer for a couple of decades not never got into DSP audio processing, so will need some help as a start point. I've been searching for the best solution for this new deve
-
ADAU1452 PVDD / AVDD on/off while IOVDD / DVDD on
Hello Is it a problem to have IOVDD and DVDD always on and PVDD/ AVDD turning on (and off) only just before DSP reset is released (is reset)? It meets the sequence requirement, but perhaps that assume
-
Filter co-efficient
Dear Team, We have tried calculating filter coefficients theoretically with following parameters Parameters: Filter Type : General Eq (2nd order ) High Pass Filter Sampling frequency(fs) : 48000Hz Cut
-
Filter Co-efficient Calculation
Dear Team, We have tried calculating filter coefficients theoretically with following parameters Parameters: Filter Type : General Eq (2nd order ) High Pass Filter Sampling frequency(fs) : 48000Hz Cut
-
Upsampling / Downsampling bug?
Hi, So I was trying to troubleshoot a project, and stripped it down to complete barebones to determine the issue. [Using an EVAL-ADAU1467Z Rev B board] Starting a completely new project & dragging in
-
Eurorack Peak / Rms to Gate
Hi, I want to get audio into the adau1701, bandpass, gate and get a signal everytime the gate is active. At the moemnt I am using the limiter for that which is working great but on the GPIO I dont get
-
When I have more than 1 Sub Harmonic Synth (low freq) control, I get "Variable 'input_zm2' is already defined in this scope"
This is the Sub Harmonic Synth (low freq), I get Variable 'input_zm2' is already defined in this scope when I have more than one in the project. Suggestions? Thanks, -Robert Audio Signal Processors ad
-
ADAU1466 : external MCLK = internal PLL ???
Hello, I use ADAU1466 with external MCLK at 24.576MHz. Fs = 192 kHz On this "program" : On IN one DAC (I2S 32 bits) - On OUT 4 ADC (I2S 32 bits). If I use "PLL clock" as "PLL CLK SRC" (with after /4 a
-
How we can find the latency of a particular block in a HDL project using vivado.
I am using vivado for HDL coding. I am unable to find the latency of each block individually in a complex project. Is there any option in vivado that specify the latency for each blocks in a project?
-
does ADAU1452 support notch filter and all-pass filter?
Hi as title, could I load notch/all pass filter coefficient to 1452 IIR table to active related function? tested even all data is correct and it still could not work. and how about the data bigger tha
-
Acoustic echo cancellation on ADAU17XX
Hi, Thanks for the recommendation to use ADAU1787 for a low-latency low-power live voice amplification project (portable megaphone). One of our challenges is to eliminate acoustic echoes. We are inves
-
What does the ADAU-1467 Delay (PM) mode do?
Hello there! I don't know what is the PM mode of "Delay (0/1/PM)"? How to use it? Can't see the changes in the phase view, please guide me. Thanks Jack wang 謝謝。
-
ADAU1701 VuMeter Missing parameter address, how can i read that?
Hi Guys, Im working on a VU Meter read from DSP, trying to read inside Sigma Studio ( on a microcontroller too), i have create a basic project, exported files and that files does not have parameters a
-
RMS and peak limiters, latency/look ahead
Hi It seems that the RMS limiter does not introduce any signal delay. Is that correct? What window length is used when the RMS value is calculated/how is the RMS value calculated? When adding the limi
-
TDM of 2x2 stereo channels between 2 ADAU1467
We have problems using TDM where one of the ports is slave to another TDM port. Here is the case: We have to transfer 4 stereo channels using two ports, port 1 and port 3 between two ADAU1467. Sample
-
Custom FXLMS algorithm implementation on ADAU1701/ADAU1452
I am currently using the FXLMS block in ADAU1452 to implement Active Vibration Control; however, I find the steady state error of the block to be too large, and I would like to implement my own algori
-
Reverberation algorithm/ modulated delay ADAU 1452
Hello everybody! I am relative new in dealing with Sigma Studio. My EVAL-Board ist the ADAU 1452. I want to create a reverberation algorithm based on allpass- and combfilters with a modulated delay. S
-
sigma studio custom algorithm
Hello, Is there a method to add a new custom algorithm to the toolbox of Sigma studio IDE. Thanks, Khaled. sigmastudio
-
How do we get access to all algorithms
According to this support post: https://ez.analog.com/dsp/sigmadsp/w/documents/5164/faq-developing-custom-algorithms-and-or-using-3rd-party-algorithms I need to "Contact an ADI engineer on EngineerZon
-
Recommendation for a processor for first project
Hey guys, I have mostly analog or general uC background and I'm looking for a recommendation for a DSP for first and further projects. I'm mainly working on audio-projects for musical instruments, mea
-
Bitrate and samplerate change realtime
Hi, as controlling a 1701 with a mcu now is working ok I was wondering whether it is possible the reduce the samplerate and the bitrate of the incoming signal so that I can use a pot on the mcu to set
-
Support for warped FIR filters
Is there any option to use warped FIR filters in SigmaStudio? Apart from putting together the filter structure from individual blocks yourself? If not, is there a chance that I can implement these in
-
Acoustic Echo Cancellation: 4kHz-peak, convergence time
Hello ADI-team, I'm testing the SigmaStudio AEC-algorithm in one of our communication products (ADAU1452) with a speaker-microphone-combination where duplex communication should be achieved. I'm using
-
Compressor formula
I need the formula/equation of the DSP compressor component. Threshold, Ratio Compressor, Ration Expander, Input Gain, Attack, Hold and Release.
-
ARM initialize ADAU1452 problem
Hi I have a problem initialize ADAU1452 in Debian by i2c. initialize data is 49xxx long and ARM driver could only write 8192 bytes per time, and how I could connect data for each transaction with STOP