EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1701
I'm repairing biamp RCF ART 715-A MK4. The filter and limiter is built on ADAU1701. The amplifier works, but white noise of medium volume is heard. I found out that the ADC1701 ADC is a noise source.
-
Changing FIR coefs
I've got a problem. I have a program for ADAU1701 including FIR filter with big amount of coefficients (like 900 or more). Also I have to use few sets of fir coefficients that cannot fit into the proc
-
ADAU1701 Delay between MCLK and BCLK/LRCLK when used as a slave device
We plan to use the ADAU1701 as a slave device. Have MCLK, BCLK, LRCLK supplied from the master side datasheet P48 has the following description "The serial data clocks need to be synchronous with the
-
ADAU1452 PEQ safeload
I'm developing a board composed of MCU and ADAU1452. SigmaStudio v3.13 is used to create block diagrams. MCU can make ADAU1452 work by I2C,also can Control the volume. SO I think I2C operation has no
-
Wind noise reduction in ADAU1788
Hi,Sir: Our company bought a ADAU1788 EVA board. We can find that ADAU1788 support " Wind noise reduction" from https://wiki.analog.com/resources/tools-software/sigmastudio/toolbox/adialgorithms/windn
-
Audio processor recommendation for megaphone project
Hi, We are working on a low-power battery-operated megaphone/bullhorn project (purpose is to amplify a user's voice). In terms of the audio flow, the user's voice will first be captured by 1 - 2 digit
-
adau1761 selfboot
Please help!! I use stm32f7 and adau1761. When loading over the i2c bus, the code loads without problems and register reading is good, but there is a need to load the code via the SPI interface, but I
-
ADAU1452 RMS and Peak Compressor Calculation
Hey together, I have a question regarding the calculation of the in-to-out gain-curve of a compressor block. In general I know how to calculate the curve but I was wondering that there seems to be a d
-
REW with Automatic EQ function and tuning without USBi programmer is that possible?
Hi, I found one topic about REW speaker tuning with ADI DSP Automatic EQ function: https://ez.analog.com/dsp/sigmadsp/f/q-a/64304/adau1701-sigmastudio-rew-auto-eq and I follow the topic step one by on
-
ADAU1452 drive strength and equivalent resistance or impedance
In the datasheet there is only information about maximum current versus drive strength setting, ie at 3.3V Lowest 2mA Low 5mA High 10mA Highest 15mA A simple calculation implies that the R-ON for the
-
ADAU 1467Z- Incorrect sensitivity measurement with ICS 41351
Hi forum, Lately , I purchase some EVAL-ADAU 1467Z for measuring ICS 41351 mem microphone from TDK. And i encouters 2 problems with this setup : +Offset 1 dB FS compared to data sheet , the value in d
-
ADAU1466 HW slew mute modules parameter host update
Good morning I'm developing a new product using the ADAU1466 SigmaDsp. My schematic contains some mute HW slew module and I'm trying to manage they from my microcontroller I've notice that if I try to
-
Downloading program from ADAU1701
Greetings everyone! I faced a following problem. I have a program stored in eeprom of the ADAU1701 development board. Obviously, the processor moves the program to RAM when it starts working. But, I h
-
Voltage Level on I2C ADAU1787/SSM3525
Hello, I am working on a configuration with both eval boards for ADAU1787 and SSM3525. I plugged the Eval-ADUSB2Z in parallel on both boards and everything works fine.( I have only one USB cable and a
-
About ADAU1452 configure data calculation documents
I wanna configure the DSP via I2C by ARM. I donwloaded EQ_Coefficient_Calculation_in_sigmastudio.pdf and have no questions in this section but I have other problems to configure I want like Dynamic ba
-
Microphone Feedback AutoControl
Is it possible to do microphone autofeedback control in ADAU1701? By this, I mean detection of onset of acoustic feedback and suppression with notch filter. Are there any pre-built blocks in SigmaStud
-
Using multiple hardware switches to select output.
I am using an ADAU1452 with custom circuitry. I have one signal source, 5 hardware momentary switches connected to ADC inputs, and 5 output devices (speakers). I am trying to figure out how to use the
-
GPIO issue in DemoUc Application
Hi, We are trying to run the DemoUC application code under SoftwareModules\SigmaStudioForSHARC-SH-Rel4.5.0\Target\Examples using ADSP-21569 EZ-kit.We are getting the audio output on running this code
-
Issue with bluetooth signal detection algorithm ADAU1451
Hi, I am running a project on ADAU1451, using Sigma Studio version 4.2 Build 1. I have 3 inputs (Bluetooth, Aux and XLR) and would like to detect and readback which input is playing. Aux and XLR work
-
Interface R/W for DAC setup
I am thinking about a small project with the ADAU-1452 and Infineon MA12070P I2S class-D chip. The setup of the amplifier chip is done with I2C, but will it be possible to do these setup changes from
-
Connecting a guitar to adau1701
Hello everybody. I'm gonna use my adau1701 for guitar signal processing purposes. It's known that adau1701 has built-in ADC and DAC and my problem is following: adau can recognize and process a signal
-
acoustic control
Hello, i'm new to dsp , and i want to control a drum acoustic response with a dsp that i have an 1467 eval board like this figure: i want to reduce some innate resonance and add new ones. Do you have
-
license questions on plug-in for Sigma DSPs
Hello to the team, I have license questions on plug-ins for Sigma DSPs. Could we talk in a private discussion please? Thanks in advance Christian
-
SigmaStudio - real time to do power electronics?
Greetings! A question on repurposing SigmaStudio and audio ICs. Is it possible to use them to, for instance, control an AC-DC power factor correction boost converter? As an example, the ADAU1787 could
-
problems with index selectable filter
Hi all, I'm developing a speaker for monitoring on a stage. I'm very happy, everything works really fine but... I wanted to implement an index selectable filter but even with the simplest schematic it