EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
High Pass Filter Response
Dear Team, We are using High Pass Filter(General EQ 2nd order Multi channel Double precision) in our application with below parameters Q factor : 0.707 Response is observed as below ->Gain at cutoff f
-
SigmaStudio Algorithm documentation
Hello, Can anyone point me to an accurate documentation of the algorithms implemented in ADAU1462 by SigmaStudio? The version 4.5 simply does not have any help. The wiki is at best completely outdated
-
Max channels per ADAU1451 I2S port and changing sample rate at runtime
I'm utilizing the ADAU1451 in a project which will be supporting up to 32 bit audio at a sample rate of 192 KHz. We designed our prototype board with the assumption that all 48 I2S channels could be u
-
ADAU701 Programming in SigmaStudio question
Hello! I am very new into this and I hope this sort of questions can be asked here... I will try to keep this as short as possible. I have a 2.0 Class D Amp with ADAU701 for DSP. I try to build a port
-
ADAU144x spdif channel status bits. How to set these?
can these status bits be set in the SPDIF transmitter. I am finding that very few off the shelf devices (only test gear can) will receive the spdif generated by the ADAU144x spdif transmitter. Its to
-
Dynamic loudness - Help me fine tune it and understand the log table
Hello everyone I have a portable speaker that I'm working on and recently implemented on it the dynamic loudness algorithm by KJBob (awesome by the way, thanks for sharing that) https://ez.analog.com/
-
Where can i find document on undocumented Toolbox algorithm
Hi , Could you let me know , where i can find information about undocumented Toolbox algorithm . Like the on in the following red which doesn't have link . We are trying to use ADAU176x. With regards
-
[ADAU1701] Possible to make a Eeprom readout and edit with SigmaStudio?
Hi guys, I have a question and hope you can help me out. I have an existing design based it on the ADAU1701. I builded a couple years ago and it still works like a charm. But now i want to edit the ee
-
ADAU1787 compile error issue
Further to my unanswered query of 5 days ago I'm now getting a similar error when I try and implement 2 parallel filter paths: anyone got any ideas what might be causing this please? ADAU1787 Integrat
-
SigmaStudio ADAU145x I2C Bitrate below 400 kHz
I have reached a disconnect between your documentation and your program. The datasheet for the ADAU145x says the Master Control Port set to I2C communication can support 20-400 kHz and the toolbox hel
-
ADAU1452
is there any algorithm in the ADAU1452 that can be used to simulate the Optocoupler NSL-32 http://datasheets.guru/NSL-32-datasheet-3903280.. I need something that the more the input value the less the
-
tone control using adau1701/sigma studio
I'm trying to implement bass and treble tone controls using external potentiometers and two of the ADCs on an ADAU1701 board. I would like something like the Tone Control available in the GenFilter2 b
-
Modified FxLMS block for ADAU1442 eval board
Good afternoon! I am wondering if it is any way to use the Modified FxLMS block or FxLMS block for the ADA1442 eval board. This board supports only NLMS block, which is not very useful for multi-chann
-
Indirect Parameter Access Table
Hello, there are some new parametersets in the selection box concerning the params of the moduls: current... and target... (see picture) What do i have to choose to write new values? Marc DSP: Adau 14
-
About the 0Hz-100kHz range signal processing
Hello, Could you let me know the DSP model that meets the following two conditions? -DSP that can be developed with SigmaStudio -DSP capable of processing signals in the range of 0Hz-100kHz We are loo
-
ADAU1966 Communication over TDM bus
Hello everyone! It's the first time that I am using ADAU1966, and it looks like I can't make it work! More specifically I am looking at the Communication over TDM bus, I am sending signals but ADAU196
-
Leitura de parâmetros no ADAU1701
Olá, utilizo o ADAU1701 conectado a um microcontrolador via SPI. Controlo o mute, frequência e amplitude de um gerador de áudio. Faço apenas escritas no DSP. Hoje preciso fa
-
ADAU1787 FastDSP probing issue.
If I add stimulus and probing blocks either side of some filters in the FastDSP it crashes out on compile. Putting them in SigmaDSP path on the same project seems to work OK. Any ideas on how to check
-
Multi ADAU1467 Configuration
HI ADI's One of my customers wants to configure using Sigma DSP(ADAU1467) as below. N DSPs are controlled by one MCU, and each DSP is connected to an 8-channel ADC and DAC. Each DSPs operate independe
-
ADAU1401 MCLK and BCLK
I am currently working on a project with the adau1401. I going to be using an spdif receiver connected to an ASRC and then to the ADAU1401. The ADAU1401 will be doing some filtering and outputting i2s
-
Group together two ADAU1701s for 8 outputs, SP/DIF, DTS/AC3 decoding
I have a pair of Wondom ADAU1701 units. I am new to these devices so some guidance would be appreciated please. have several queries: I would like to know if it is possible to build something like a 2
-
ADAU1701 - Exported system files are way too big
When exporting system files for my SigmaStudio code, the compiler of course knows the data and parameter RAM utilized by my code, but when the system files are exported, the arrays for the program and
-
ADAU1761 full scale output on serial port
Hello, I need some help understanding the serial port output numeric format from an ADAU1761 CODEC on a custom PCB. I've set up the CODEC for ADC single ended line in routed directly to serial port ou
-
ADAU 1452 Need help with the input selector and the MUTE button
I am an inexperienced user of Sigma Studio. 1. I ask you to help with a real-life example of a project with a switch between two inputs controlled via the AUX PIN switch button. 2. How to make the fun
-
Sigmastudio 4.5 exported command inconsistency
Dear engineer, In developing MCU for ADAU DSPs, I found some inconsistency among codes exported from bootload button and modes button. It mainly comes from length in function "" //********************