EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Need hints on use of two control ports on advanced sigmadsp processors
Hello, On the advanced SigmaDSP processors, there are two control ports. One is a master (used for self boot) and the other is a slave. Can anyone throw more light on why two control ports are needed/
-
ADAU1462/66 or ADAU1463/67
Hello, I am making a jump from ADAU1701 to either ADAU1462/66 or ADAU1463/67. From the datasheet, it is obvious that the 63/67 has more hardware resources in the form of # of AUXADC, and GPIO pins. Be
-
Serial Port Format - Where's the LSB?
I need help understanding the data format for I2S serial ports. I have configured an external device to send I2S data to the ADAU1452 in 24 bit format and it appears to be working. The issue I'm havin
-
ADAU1463/ADAU1467 Power Supply Design
Hello all, I'm starting the hardware design for the ADAU1467, and I have a few questions: First Question - I plan to use 5V main power supply, and I plan to minimize current consumption to minimum as
-
Master Control Port Runtime Sequential Write - Dynamic value
I am using an ADAU1462 and am having a hard time writing a value, decided on runtime, to I2C. Is it only possible to write hard-coded values, defined in the sequence file, to I2C? I have been trying a
-
Safeload using I2C on ADAU1787
Hi ADI I am busy developing code for an ADAU1787 connected to a MCU via I2C. I am able to connect, load code and communicate with the SigmaDSP. Using direct memory writes I am able to change the gain
-
EVAL-ADAU1467Z \ Audio Mute Using GPIO
Hello all, In my project, I'm using the EVAL-ADAU1467Z I want to use the mute function in a specific audio path, and I need to control the mute function using a GPIO input pin (Logic High = Mute, Logi
-
EVAL-ADAU1466Z input data to file
Dear ADs Team, I am new to EVAL-ADAU1466Z and SigmaStudio. I am wondering if there is a sample SigmaStudio project performing data 'recording' from an input line, say 'I/O 1', to a single txt/ASCII fi
-
Internal Mute Control (ADAU1452)
Hi there, I have multiple outputs from my ADAU1452 that each have an individual mute. This is great. However, it would be nice to have one MUTE control in my design that would mute all of the outputs
-
AD1939 CODEC sample rate
For the AD1939 CODEC, data sheet specifies sample rates of 128/176.4/192 kHz if you set control register to '10'. We did that and are at 192 kHz. How do we get 128 kHz instead ? That's the ADC/DAC sam
-
Writing parameters to EEPROM memory by MCU
I just started my career studying the ADAU1701 audio processor. Now I’m trying to figure out how to write to memory. I am trying to write data to memory through the i2c interface, using the arduino, b
-
Changes in Probe plots when sampling frequency modified
Hi, I have a very strange behaviour with the Probe and Stimuli blocks. I am using SigmaStudio 4.5. With an ADAU1701: - When using an Nth Order filter between input and output, the plotted frequency re
-
ADAU1452 spi slave mode : datasheet says mode 3 but USBi actually uses mode 0
Really two questions: 1. How is it that is works with either mode without (non existent) re-configuration? It looks like all the data will be shifted by 1 bit if you use the wrong mode. But it seems t
-
ADAU1787 DAC single ended output from differential output
Hello, ADAU1787 has a differential DAC output. My application needs a single-ended output and I am wondering if I can simply ground the negative pin of the differential output? If not, do you have a r
-
ADAU1761 Balanced input gain control question
For my design I configured ADAU1761 inputs as balanced and want Left Volume Control to adjust left channel gain. Unfortunately, I don’t see any respond when I am changing input gain. The LDBoost is wo
-
communication error
Hello, I'm using the EVAL-ADUSB2Z board (Win 10 64bits) with the iUSB drivers installed and green box on the hardware configuration. However, when I click "Link Compile Download" I get a connection er
-
What the difference between signal add with Mixer?
Hello, I have see the two module, one is signal add, the other is mixer if I set all the switch value to 1, like this then the result of two module is same or not, if difference, why. Thanks.
-
Algorithm development in a DSP
Dear: I am interested in learning how to program my own sound algorithms on a DSP. This would be for educational and research purposes. I work at a university (UNTREF, Argentina), in the career of sou
-
ADAU1701 Noise removal algorithm
Hello, where I can find a Noise removal or Noise reduction tool for ADAU1701? I cannot find any noise tool in the ADI Algorithms table or in any other place.. Thanks Audio Signal Processors SigmaDSP A
-
ADAU1467 ASRC
Have noted that its possible to use sample rates higher that 192k as input to the asrc, for example 384k. Have tested it on the adau1467 eval board. The ASRC0_RATIO register 0xF582 correctly responds
-
ADAU1787-Upsample and Downsample of Fast Core and Sigma Core
Hi all, I need to use ADAU1787 in low latency(A2A less than 100us) and low sample(12kHz)。In the Sigma Core or Fast Core, can I downsample the data of ADC from192k or 96k to 12kHz without filter, and c
-
Fourier Analysis & Wavelet Analysis
hi sigma studio need help, how to do Fourier Analysis & Wavelet Analysis with adau1701 or other? Audio Signal Processors SigmaDSP Audio Processors adau1701
-
How to reset other ICs in the ADAU1701
HI, I plan to do some small tests.I tried to reset other ICs using DSP, but found that the reset operation would be repeated all the time. Is there any way to make the reset action only once Best rega
-
How to configure potentiometers
Hi, My ADAU1701 DSP board have 3 potentiometers connected to MP3, MP8 and MP9 into the AUX-ADC input.- I have uploaded a capture from the developer's example. This is for master volume control. And th
-
Inconsistency between Coeff. Calc filters and general filters
Hi, I am using Sigma Studio v4.4 on ADAU1462. There seems to be an error in the Coeff Calc. filters. When set to parametric mode, the gain measured at the output is only half that which is set in the