EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Trouble with rotary-encoder volume control on ADAU1466 evaluation board
Hi, I'm trying a Bourns PC11R series rotary encoder. I built the suggested filter circuit shown on page 2 of the datasheet. I connect terminals A and B to GPIO pins 12 and 13, which are labelled on he
-
Can the ADAU 1701 be used to multiply two audio waveforms in real time and output the product result?
I'd like to multiply one audio waveform by another (product) and output the result (e.g. modulate). Can this be done? Frequency range feasible? What about square wave modulation of a relatively high f
-
Filter Implementation AD1941
Hello, I am trying to implement FIR and IIR filter in AD1941 DSP board. Can anyone please provide me any guideline from the beginning or help me with the code. Another question is AD1941 board is ok o
-
[BUG REPORT] [ADAU1452] High order Shelving Table Interpolator with Ext gain or not, trigger "index out of range exceptions" and totally locks any file saved that contains them.
Sigma 4.5. Steps to reproduce: start a blank project add one of those filters grow them to more than one cell (grow algorithm) save close try to load again The use of this module also comes with a var
-
Cascaded filter calculations clarification
Hi, I am looking for a quick clarification on how to calculate the frequency response of a given crossover filter. I have been using the FilterMathCalculations.pdf (attached) to calculate my coefficie
-
Connecting ADAU1452 to the programmer
Hi. I have problem connecting the EVAL-ADUSB2EBZ programmer to my custom ADAU1452 board. 12.288MHz sine wave is present on XTAL pins DVDD is 1.2v and other power pins are on 3.3V SELFBOOTis shorted to
-
Loading control parameters from flash memory to DSP
We need to 'load different sets of control parameters in the run time' for the different modules implemented(like Volume control, Mute, Delay). >> We used sequence window for this, and saved different
-
How to update fastDSP parameters with the sigmaDSP?
Hi, I have an EVAL-ADAU1787z and I'm trying to build an application in sigma studio where I can update the biquad parameters on the fastDSP from the sigmaDSP. From the manual I can read this: "There i
-
ADAU1462: loud pop/click when audio starts
Just completed a board that uses the ADAU1462to read audio through the S/PDIF optical input. The design closely follows the ADAU1466 evaluation board, with a self-boot EEPROM (which I successfully pro
-
Update parameters on the FastDSP with the SigmaDSP
Hi, I just received a development board for the new ADAU1787 (EVAL-ADAU1787Z). As I understand it I should be able to update parameters on the FastDSP, with the SigmaDsp. Meaning I should be able to w
-
Loading Preset values for In Built Blocks in Sigma Studio
Dear Team, I am using Multiple Individual Volume Control and Mute Blocks which are available in sigma studio,can you help me understand how to give preset gains to the available volume controller bloc
-
ADAU1452 and I2S together
Hi all, My question is going to be a really basic one, but still, I can't figure out the setting in sigma studio. About the setup: WW8804 SPDIF -> I2S eval. board's I2S output connected to ADAU1452 ev
-
ADAU1450 multipurpose ports MP0/1/2/3/6/7 LED drive?
Hello all, The datasheet of the ADAU1450 states that digital output ports cannot be used to drive a LED (page 8: $Electrical Characteristics, Digital Input/Output). Nothing is said explicit about the
-
setting up AD2410WBZ TRS input and output(along with A2B soundcard v1/v2)
Hi, I am setting up a schematic to demonstrating A2B capability to do recording and playback via A2B. What we have here are A2B soundcard v1 and A2B soundcard v2, along with some AD2410WBZ and AD2410W
-
Use multiple ADAU on a single SigmaStudio project
Hello to everyone. I'm experimenting to design in a unique SigmaStudio project the use of three ADAU1452 to be sure that exported constant referements in include file are not equivocable. So I I have
-
C math libraries for filter coefficients calculations on MCU
Hi, i am use 1452 DSP with STM MCU, my SigmaStudio project have several filters: HPF Hanning with variable Freq and orders LPF Hanning with variable Freq and orders All Pass with variable Freq, gain a
-
ADAU-1787 simple low instruction signal adder
Hi there. Is there a way to add two signals on the ADAU-1787 FDSP? I can just find the 'multiple control mixer' and want to use the FDSP resources as economically as possible. Thanks a lot, Christian
-
ADAU1701-Mute problem
PDF Dear ADI Please see my project of a simple crossover module. When I pressed mute1 block We can hear a strong popping in the speakers. What is causing this? What can I do to eliminate this problem?
-
Ultra-strange filter problem..
Hi! While evaluating the second revision of my DSP board, I noticed some super strange behaviour that is caused by a 2nd order lowpass filter. See for yourself. This is basically what you would expect
-
ADAU1466 overheat ?
Hi ! I would be interested in what happens to an ADAU1466 if it overheats, to compare that to the strange behaviour that I am currently experiencing. In the current revision of my DSP board, I am stil
-
Biquad coeff calcs don't match
Hello, I'm controlling a parametric EQ and testing my system but not coming up with the same coefficient results as Sigma Studio. Could someone verify the maths that is used please? Cell Name: Zone1_E
-
Unable to place USBi in SPI Mode [EVAL-ADAU1466Z]
Hello, I am trying to connect the EVAL-ADAU1466Z to my Windows 8.1 computer. Per the user guide the USBi should be in SPI mode. However the D3 SPI LED on the USBi will not illuminate. The USBi is in I
-
ADAU1701 State detection
I can read the input size of label 3 in the MCU. Why ca n’t I read the input size of label 1 and label 2?
-
EVAL-ADAU1467 Noise Floor
We just purchased an EVAL-ADAU1467 from Digikey and I believe it must be defective. Using a direct input to output connection in the DSP, what should the expected noise floor be? I am measuring approx
-
adau1701 pushbutton volume control
Hello, DAVE, I am using ADAU1701 MP2/MP8 GPIO as pushbutton to control volume with MCU. MP2/MP8 10k resistor pullup which is active low. these 2 GPIO nothing else use only for button. the project atta