EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Does ADAU1451 can connect or generate a short jingle voice in the dsp core?
Hello, i am designing a multi-source of audio speaker , it has 4 audio sources , AUX/USB/SPDIF/WIFI. now each source works . at the source change moment, i like it has a prompt voice, like " USB MODE"
-
ADAU1772 SAI configuration for MCU
Hi, Im working on project where I have STM32 mcu and ADAU1772 codec, plan is to get readings from 4 analog signals and process them on mcu. I managed to link my sigma project with firmware. How do I s
-
sine source not working when flashing the ADAU1701 over I²C
Hello, I'm working on a project where i control an ADAU1701 with an ATMEGA328 via I²C. Everything in the DSP is working fine, except a signal generator. I use a sine source and when I'm linking t
-
Volume Based High pass Filter
Hello, I am new to this and am trying to use a wondom amplifier with adau1701 built in to make a speaker with dsp. Basically I wanted to shift a high pass filters center frequency from 12Hz at the low
-
ADAU1701 works with active xtal?
Hi Guys, 1) I want to know if ADAU1701/1401 works with Active Xtal ( 4 Pins ones, with GND, Vcc and Out ), if yes, a) Out is to be connected to MCLKI? b) OSC0 is left floating? 2) Also, i want to know
-
Frequency Detection Using FFT
I am using ADAU1452. I want to mute a particular channel by searching for a sine wave of 400 Hz to 500 Hz. (ex. siren) If I implement this circuit, can I read the frequency and level values I want fro
-
Chebyshev 24db algo need.
cant find ifo about high order chebyshev algorithms need 24, 36,48 24 db very needed...
-
EVAL-ADAU1452REVBZ
Hi, The customer has implemented the peaking filter transfer function in Python, and has a question. It appears that the peaking filter maximum is twice that of the gain that they have set. For exampl
-
ADAU1452 Flash eeprom with microcontroller
Hello, In order to update my products, I need to flash the DSP's eeprom for selfboot with a microcontroller. For ram footprint reasons, I can't send the spi data at once (i.e. I can't send all the byt
-
ADAU1452 Coeff Calc IIR block gain is 1/2
Hi, I am using the IIR EQ block that uses the inbuilt coeff calc generation. Where the parameters are entered as Gain Q and Freq. Rather than the standard 5 coeff's The Simulation Probe indicates that
-
ADAU1467 self boot EEPROM issues
Hello Everybody, I am having some difficulties with the selfboot EEPROM. I am making a program with a FIR filter loaded with a table of 5500 taps, If I grow it with an additional channel (for to have
-
SigmaStudio force readback controls subsequent i2c addresses
Hello all, I was wondering, is it possible to have a few readback controls in SigmaStudio (for a ADAU1452 DSP) with their I2C addresses forced to be subsequent? What I would like to do is implementing
-
ADAU1452 no data in
Hi, I'm trying to get an ADAU1452 running in a very simple setup using SigmaStudio 4.4. It's basically the following: I2S (48kHZ, 32bit) -> SDATA_IN0 SPDIF -> SPDIF_RX The DSP is fed with a static 24.
-
ADAU 1452 FIR length Sigma Studio
Hi all, Am I right assuming that, if I want to implement a FIR filter in Sigma Studio for a ADAU1452 of 2400 taps, I have to set the length in SigmaStudio to 2401? I've read somewhere that the last co
-
EVAL-ADAU1452REVBZ-UG-1662
I need an all pass filter of 1st degree with dynamically tunable characteristic frequency (i.e. 90 degree frequency). The phase shift used would be 0 to -20 degree and the frequency bandwidth of the t
-
ADAU1761 SigmaStudio 4.1, detail information about Fixed / Beam Forming Designer
I use the ADAU1761 with the Sigma Studio ver.4.4. In the Tool Box, we can find two beam forming function - Adaptive / Adaptive Beam Forming Algorithm - Fixed / Beam Forming Designer But in the on-line
-
How to save volume / treble / bass into EEProm on self-boot mode of ADAU1701?
Hi everyone: I am a newbie.I DIY a project using ADAU1701. The specific UI is: Use an encoder with buttons as input. 3 IOs will be used. Use 3 LEDs as an indication that the current encoder should adj
-
10 Band Equalizer controlled with potentiometers
Hi everyone! I'm trying to build a 10 band equalizer with an ADAU1701 (no µC). Because there are only 4 Aux ADCs, I want to link the analog signals from the 10 potentiometers through one ADC wit
-
general FIR adau1452
general fir in high pass not work on low freeq. 200-500 hz have no effect. it start to work after 4000 hz approx. Audio Signal Processors adau1452 SigmaDSP Audio Processors
-
Is ADSP-21489 Powerful Enough to Run
Hallo We are planning to buy a ADSP-21489 evaluation board. For the moment i downloaded Sigma Studio, Sigma Studio for SHARC and the recent version of the Cross Core Embedded Studio. I have to impleme
-
4 group I2S in adau1451 , only SDATA_IN0 works
Hello, I am using ADAU1451, there 4 audio sources, AUX/SPDIF/USB/ WIFI. AUXIN -->ADC-->SDATA_IN3 USB (I2S)--> SDATA_IN2 WIFI(I2S)-->SDATA_IN0 SPDIF--> ASRC INPUT 0/1 Now , WIFI(I2S)-->SDATA_IN0 works,
-
ADAU1787 - Exporting Sigmastudio Project to C code
Hello team, My customer is facing some issues using SigmaStudio 4.4: The project they developed uses a microcontroller that communicates with ADAU via the I2C bus. The data that is sent to ADAU for in
-
Latency in Sigma DSP
Hi Team! I have a doubt regarding how much is the system latency in ADAU1452/ADAU1467 .This is not to be confused with the processor latency which could be the time it takes for data to traverse from
-
ADAU145x Sine Tone oscillator dB unit
Hi, There is a Sine Tone oscillator module for ADAU145x. Please let me know the exact unit of gain [dB]. Does this [dB] mean [dBFS]? Thanks and Regards, sigmastudio adau145x SigmaDSP
-
Need help removing poping sound
Hello, I am new to DSP's and I have inherited a project that i need to support. I have included an image of the audio path below with the area of interest highlighted. We are currently using an ADAU14