EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Recommended SigmaDSP Model To Start With
Hey guys, I've been looking into the SigmaDSP line and was curious what you would recommend for getting started in SigmaDSP? I have intermediate experience with DSP systems but no experience with Sigm
-
[ADAU1452] Reading data from E2Prom
Hi Team, We tried to view the flashed hex data in E2Prom chip using "Read E2Prom to Display" option in sigma studio but data 'zero' is displayed in all memory location. The flashed code working fine i
-
Poor frequency response - simplest config!
Hi all, I'm used to running much older versions of SigmaStudio - now on to 4.4. Encountering something really weird. I have a small audio device I'm planning to EQ with the 1466 DSP. I measured the de
-
Sigma Studio Crashing Loading
I've downloaded a fews version of Sigma Studio (4.4, 4.2, 3.6). It runs fine until I try to open a sigma studio file, then it closes every time after approx 20-30sec. I can't find any output or messag
-
SELFBOOT through I2C, with pause/halt
I am considering to build a system with a ADAU1452 working in SELFBOOT mode over I2C. Instead of having a I2C EEPROM I plan on having a MCU working as I2C slave delivering the firmware to the DSP. My
-
Sigma Studio Volume Control Parameter
I have a product that uses a number of volume controls which I have been controlling using a small table of pre-set gain values. The table values were obtained using the capture window in Sigma Studio
-
Resolution of the pictures in the answers
Hello, how can I get a picture with high resolution? whether I amplify the pictures or not, it is hard to see the content of the picture clearly.
-
Replacing ADAU1442 with ADAU1467
Hi, for a redesign of a system with ADAU1442 and 5 AD1938 i want to replace the ADAU1442 with the ADAU1467. I try to remove the ADAU1442 in the hardware config, there is an error message "The selected
-
Sliding DFT on ADAU145x
Hello, I would like to implement a stable sliding DFT, but I am facing with the scanning of the lookup table so that it scans a frequency from 20Hz to 24Khz in a sampling rate of 48Khz. I don't know h
-
External Control of parameters EVAL-ADAU1466Z.
I just ordered my Eval board , downloaded Sigma Studio , looking around a bit as I wait for the board. One thing that puzzles me at the moment , It seems like most controls are static ? I see that I c
-
Problem with mute
I found problem with muting - ADAU1466 and sigma studio (4.1 ... 4.4 ) Mute/No Slew/Mute block works only with 3 channels. When I use 4th block of mute, it not works! It is automatically on/off about
-
Indirect Parameter Access Table cannot be used with ADAU1452
I want to use it for crossover block control via I2C. After completing link compilation in my project, it is not selectable. I learned from the following link that it would be invalid in older version
-
No sound on channels 4 and 5 - EVAL-ADAU1467Z Rev. B
Dear: First of all I would like to apologize since I am new with this type of DSPs. I recently received the EVAL-ADAU1467Z. I have managed to input audio through channels 32 and 33 and output audio th
-
High pass
Hello, Why I doesn't get a high pass when I subtract the original signal with low pass output (output from my FIR) ? That should work where it is wrong ? Test_IIR_custom_FIR.dspproj.zip
-
Loop ADAU1451
Hello, Is it possible to create a loop in Sigma studio to execute low level bloc (multiply, add, and so on) ?
-
In ADAU1452, inbuilt algorithms supported in Block schematic & schematic to be combined
We are using Sigma studio version 3.17 in our project for ADAU1452 processor. Modules implemented in our project is block based, we need to use the filters modules supported in schematic(Sample based)
-
[Bug Report] Exported Sequence contains wrong Byte count
Hello guys, I am currently encountering the issue, that when I export my Projects System-Files after compiling, they show me the correct count of Data-Bytes. #define REG_SOFT_RESET_IC_1_BYTE 2 ADI_REG
-
General FIR
Hello, I finally succeed to display the curve of my filter FIR with my parameters here below: Hz Gain 0 0 1990 0 2000 100 5000 100 5200 10 8000 10 8200 0 FIR_G.zip What I don't understand, it is why t
-
Learn ADAU1701.
What is the best way to learn with Adau1701?. I have the EVALUATION BOARD. I don´t know if there is a book or tutorial in web with differents steps or levels like a beginner, intermediate and ad
-
Prevent poping-noise while programming
Hi ! I've had popping noise (DC) on the ADAU1466 and ADAU1701 while programming. It seems that the Soft Reset and Hibernate commands in the programming sequence are causing this. I've tried having a G
-
Lack of resource about beamforming function in 1701_dsp!
I want to use the function of beamforming in 1701_dsp to conceal the ambient noise of headphone. However there is nothing about the this fuction. If it's possible, pls give me some detailed resouses,
-
Test canonical form IIR
Hello, I realized a canonical form of IIR filter, and it seems well to work, but I don't see its response on the graph of the probe, why ? Can we impose the area of datas DC (DM0,DM1) or it's Sigma St
-
Access bit or register to know if a algorithm is completed (ADAU1451)
Hello, I would like to use an ADAU1451 to do a custom algorithm, with a cpu host (i.e. Raspberry pi) to get the result of this algorithm on this last one, is it possible and how to do ? (Use the ADAU
-
How to make options from the filter_modules in 1701_dsp?
Espescially in the second order_filters, there are parameters , general HP/LP..., and butterworth/bessel modules to make choise. What are the difference among them? And how can I make options from so
-
ADAU1701 Running at 48Khz receive I2S at 44.1Khz, needs external sample rate ic converter?
Hi, Im new on DSPs, so i have a few questions, not a bluetooth one. About Hardware: 1) I want BT audio input at 44.1Khz on ADAU1701 I2S Input and at Outputs 48Khz, i will need an IC sample converter?