EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1467 8kHz sample rate
Hello! we want to use a existing ADAU1467 design with 8kHz sample rate. Therefore 48kHz input shall be routed via ASRC to the core DSP. There computet with 8kHz due to Performance limitations (Long FI
-
No way to use ADAU1701 Class-D amplifier
I´m really disapointed with the performance of the outputs DAC0 and DAC1. No sound at all! I´m using the Evaluation Board UG-072. It should be easier to get a simple sound. Do I have to se
-
Sigma Studio signal detector hold time is too long
The signal detector block in Sigma Studio has a minimum hold time of 2 seconds. This is way too long for my application. Is there a way to decrease the hold time to around half a second or less? Ideal
-
sample comparison of a block
Hey, I am using sigma studio for ADAU1452 development kit. I have a block of size 512. I want to take the first sample and make some arithmetic operation to it. The other 511 samples follow another op
-
Downsampling from 192kHz ADC to 96kHz System Sampling Rate ADAU 1452-66
Hello, the ADCs 192kHz rate must be converted to the general ADAU rate of 96kHz. The ADAU provides the master clock for the peripheral devices. Could operate the inputs with 96kHz and drop every secon
-
4x8 DSP using two ADAU1701
The Dayton DSP-408 has two ADAU1701's to make it a true 4x8 DSP. How would I be able to do this on my own? I have the Sure APM2 that has a ADAU1701. Is it somehow possible to transport audio between t
-
ADAU1701 I2S-2 OUTPUT WAVEFORM PHASE INVERTED
Hello again, This is a same report as I post before (It was flagged and rejected treated as a SPAM post) I have developed ADAU1701 single board which has three I2S output features. I connected three e
-
ADAU1701 EVAL Board Speaker Sound Cracking.
Using EVAL ADAU 1701 . Powered UP with USBi , Batter , and Barrel comnector. Speaker sound Cracks/Clips at at Above 40% Volume . Input is from Cellphone via Aux cable to Analog IN (headphone Jack). So
-
ADAU 1701 EVAL board DAC0 and DAC1 Output sound Cracking
Hi , i am having problems with EVAL ADAU 1701 DAC0 and DAC1 amplifier outputs. The sound gets clipped/ cracks at bass notes when i increase volume above 40%. Powered the board uaing the USBi and 5V DC
-
Are you developing a SigmaStudio for iPad?
I heard through the grapevine you may be developing a SigmaStudio app for iPad Pro? Can you confirm or deny this? This would be pretty awesome and really powerful if true. sigma studio Ipad app sigmas
-
ADAU1701 SDATA_OUT2(I2S-2, DIG4/DIG5) Inverted Data Issue
Hello I was developed my own ADAU1701 single board which has three I2S output connector (SDATA_OUT0 / SDATA_OUT1 / SDATA_OUT2). I've tested this feature with my PCM5102 DAC boards. I checked with Sigm
-
SigmaStudio Tone
Hello, I would like to know how to set the parameters of Tone control and how to calculate it
-
ADAU1787 and missing microphone inputs
Hi, I'd like to have 2 more analog MIC inputs so is there any other way to add them than to have one more ADAU1787..? Regards, Osmo ADAU1787 Integrated/Special Purpose A/D Converters Audio CODECs
-
Cannot write to ADAU1451 at more than 70KHz using I2C
I am using pic32mx470F512H as I2C master and have ADAU1451 DSP as a slave device. The max allowed frequency for ADAU 1451 is 400KHz as per datasheet. Currently if I set the I2C clock at 70KHz it works
-
ADAU1701 DAC2&3 noise
Hello, I use ADAU1701 as crossover for loudspeakers. Its on freeDSP Classic SMD B board. Sound from DAC0&1 is OK, no noise. But DAC2&3 have unacceptable high noise. I would describe it as white noise.
-
adau146x AES3
Hi, I have a nice working mixer recorder prototype working well using ADAU1467 with 16 channels analouge IO. ADC DAC etc. I'd like to make an AES3 digital IO card to add to the design. I see in the AD
-
ADAU1787 FDSP filter design on SigmaStudio
Hi, I am having a problem on configuring filter for ADAU1787 FDSP on SigmaStudio. I set up the sampling rate of FDSP to 768kHz and SigmaDSP to 48kHz. In SigmaStudio, I configured 2nd-order butterworth
-
ADAU1701 no output on internal DAC's
Hi, I made the following Project "DSPRiaa-I2S in". The I2S Input is routed to I2S out and the digital Signal is ok. However for easy measuring the signals i wanted to put the Output to the internal DA
-
Zero Comparator for ADAU1452; SigmaStudo V4.2
Some while ago I asked about driving a GPIO output pin from a signal (1Hz square wave oscillator) and was directed to use a "Zero Comparator". I'm now on an ADAU1452 and I want to do the same thing bu
-
Help with safeload of ADAU1701
Dear All, I have read the FAQ about how to implement safe loading of parameters in the ADAU1701 and I thought I had got it spot on. But I have a weird bug. I'm trying to implement a simple volume cont
-
ADAU 1452 MasterSPI not working
Hi, I´m trying to get my program from SigmaStudio 4.4 to the EEPROM connected to my ADAU1452. The DSP is connected via the I²C-Slaveport to the PC. The EEPROM (25AA1024) is connected via SP
-
Time measuring or other way to build the TAP tempo button
Hello colleagues! Have the ADAU1701 board and trying to made the tap-tempo algorithm without external control such Arduino. General idea use the VCO as the tempo function and i can not suggest how to
-
Regarding EVAL-ADAU1466Z
Dear Team, I am an active researcher looking forward to provide an Active Noise Cancellation solution to a potential customer. I was going through the data sheet EVAL-ADAU1466Z_UG-1135.pdf. Our typica
-
ADAU1761 Signal Detection Time_Constant Algorithm
Hello, I am using the signal detection block in the ADAU1761, but cannot find any information in the SigmaStudio help, the engineering forum, or the Wiki pages about the actual formula used to generat
-
Read feedback signal level with SPI
Which level detector to use for get signal level? I need read over SPI signal level. In sigma studio is more level detectors, which show me signal level (average in given time). How can I read it with