EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Sigmastudio read i2s to set filters, etc
I have both adau1701 and 176x DSPs. I want to send the DSP filter, oscillator, etc settings over i2s. Is this possible? I want to be able to send various settings to the DSP though i2s from a micropro
-
Maximum delay on ADU1466
I need help, what is maximum memory used for delay, when I want to use all 4 serial imputes (8 channels). All channels will have independent dalay, connected to serial output. What is maximum delay fo
-
Shelving EQ coefficent equation - slope factor "S" documentation currently unavailable
I am trying to find the slope factor "S" for the high/low shelf EQ filter equations listed in the Wiki, but the only reference I could find is this outdated link: http://www.musicdsp.org/files/Audio-E
-
ADAU1452 and 32bit Word Samples with Filters, Delay, and Volume Control - Confirmation
Hi, If possible, can someone confirm whether the following is possible with the ADAU1452 and Sigma Studio 16bit/44.1kHz, or 24bit/48kHz I2S signal is input on one of the ports directly to the ASRC, co
-
ADUSB2Z 1.4 connection problem
Hello, I got an issue with an ADUSB2Z 1.4 that is only rarely connecting to our ADAU1452. The hardware setup is: and I very often get the following message: Reconnecting the USB cable, exchange USB ca
-
Downsampling/Upsampling blocks up to 64
Hello, I have a specific processing structure where I need to work at 750Hz (48k stream downsampled by 64). But because the downsampling/upsampling blocks are maximum 16, I do 2 downsampling/upsamplin
-
How to check the main clock is functioning
I have an ADAU1452 system with 24.576 xtal clk. sigmastudio asks for a pll clock source (direct from MCLK pin or PLL), but I cannot find that switch in the datasheet. sigmastudio fs is 96khz. the MCLK
-
Fan Noise cancelling Issue
Hi ADI's One of my customers is considering developing a fan noise reduction solution. she wants to reduce fan noise on equipment (air purifier) to reduce noise in work area. The devices under conside
-
ADAU1701 MP2 MP3 push button as volume control
Hi I am trying to assign the MP2 and MP3 for volume control according to GPIO conditioning "PushButton to control Volume" help instructions. I got compile error of "RAM address exceed 2048" please see
-
The order of changing several cell parameters in ADAU1701 by an external microprocessor.
Hello! The circuit has some kind of cell, such as a switch with two positions. I look at the memory allocation and see that this cell has two parameters, with addresses 13 and 14. Cell Name = SW1 Para
-
convert dB to signal
I need help with Sigmastudo - ADA1466. I communicate with DSP with SPI. For setting one value I need use DC input - but value will be set in dB. How can I transfer this dB set values to signal ? I nee
-
VC-delay
Hello, Using Elektor adau1701 DSP board and Sigma Studio 4.2 64bit I don't understand the behaviour of "MultiTap Voltage Controlled Delay" (see attached "Schematic.jpg") If the MAX-Value ist lower tha
-
Convolution Implementation for ADAU1466
Hello, I am trying to implement a process that involves convolution in one step, but I am having difficulty. I have made a simple testbed project in SigmaStudio that routes a stereo input through bloc
-
SigmaStudio read register API
I have an ADI Evaluation board with AD2425 A2B Bus (Master node) and ADAU1452 on it, I have also a slave node with AD2415 A2B witch connected with an MCU via I2C. Is there an SigmaStudio API to read t
-
Gilnei
Hello I am in doubt, where to connect the 4 wires of the USB in the board with the ADAU 1701 the 5v and the ground or neutral ok, but the other two. Can you help me? graciously Gilnei
-
Why is the address of the ‘Multi-Tap Mixer’ module the same?
I want to modify the parameters of ‘Multi-Tap Mixer’ module through i2c, and find that the addresses of multiple modules are the same 0x0000. What's the problem, Master? Successfully compiled and down
-
ADAU1451 self-boot failure with I2C ROM
Hello, I have a design where an ADAU1451 attempts to boot from I2C ROM at power-up. Self-boot pin is always high and 1451 reset pin is controlled by a connected MCU (Kinetis K22). Monitoring the boot
-
Alsa control generation for filters (feature request for sigmastudio)
Hi, I am using the adau1761 in a linux environment where I have built my project in sigmastudio and thereafter used the linux fw-tool to generate the binary from the project xml-file. When I have load
-
Change parameter before selfboot is enabling audio output - ADAU1452
Hello, we use selfboot to run the DSP program and at the moment we have the problem that the volume and mute are written by the uC over I2C which works fine but at boot-time the selfboot loads the par
-
writing to RAM in the ADAU1452
hi, I am trying to split a block of data created by Sigma Studio that is to be written to the ADAU1452 RAM block starting at address 0xC000. The Sigma Studio file has grown large enough that my contro
-
How can I find FFT output signal on ADAU1452
Hi ADI's Plan to use the ADAU1452's FFT block for echo noise cancellation. Noise from an irregular frequency enters the system, and FFT frequency analysis is considered to be useful for this noise can
-
PLL Loop-Filter wil be down from 1.5v to 0v when non playing music on ADAU1701
We are doing a system with 1*i2s as input and 3*i2s and 1*DAC as output. We using ADAU1701 as Master running on 48K sample rate with a 12.288Mhz osc. The issue I faced is when there is data from i2s i
-
I2C Safeload problem on ADAU1452
Hello, we try to write to the safeload mechanism from a PIC24FJ128GA108 uC over I2C to an ADAU1452 DSP. In the compiler_output.log the SafeLoad_Module addresses have been verified. In the first step w
-
Square / Sawtooth / Triangle Wave Frequency Control
I've just started learning SigmaStudio, using the EVAL-ADAU1701MINIZ, with the end goal of creating a mini synthesizer with external controls. One requirement is external control of the frequency of s
-
ADI_SigmaStudio-Rel3.15_BETA-x86
Hello everyone, I need to download the old version of SigmaStudio ADI_SigmaStudio-Rel3.15_BETA-x86. Someone can tell me a link, I can not find it. If Analog does not allow the download of this version