ΣSigmaStudio Ask AI Русский Log in

Hi. Is it possible to connect I2S on three wires: LRCLK, BCLK, DATA, when using an internal oscillator? In this case, the signal from the ADC is lost, there is noise at the DAC output.

SigmaDSP & SigmaStudio AndreiSemkiv Mar 26, 2018 00:00 6 replies Original on forum ↗
Subscribe
AndreiSemkiv Question
Mar 26, 2018 00:00

Is it possible to connect I2S on three wires: LRCLK, BCLK, DATA, when using an internal oscillator? In this case, the signal from the ADC is lost, there is noise at the DAC output.

DaveThib Reply
Mar 26, 2018 00:00

Hello andreisemkiv,

I really do not understand what you are asking. I apologize.

When you use an oscillator cell in SigmaStudio it goes directly out of the serial port. It has nothing to do with LRCLK,BCLK or SDATA . Those are functions of the serial ports not anything to do with an audio signal source inside of the DSP.

Are you talking about the MCLK
(master clock) oscillator? There is no internal master clock oscillator. There is a circuit to allow you to use a crystal to be a master clock but it is not an oscillator without having a crystal connected.

IT might be helpful to show a block diagram of what you are trying to do? A schematic might be helpful as well. Then you should attach your SigmaStudio project and possibly a small explanation of what you are trying to do with the DSP.

Thanks,

Dave T

AndreiSemkiv Reply
Mar 26, 2018 00:00

I'm sorry I did not assign DSP, it's ADAU1701. Problem: There is no sound from the I2S input when using a connection on three wires (Sdata, RLclk, Bclk). I apply the scheme. Sorry for my english.

Thank you.

c7a15e7fb40a35e5d4ca2d99a3ee700e.png
c7a15e7fb40a35e5d4ca2d99a3ee700e.png
c7a15e7fb40a35e5d4ca2d99a3ee700e.png-620x378.png
c7a15e7fb40a35e5d4ca2d99a3ee700e.png-620x378.png
43925448f9fa413a56b88afbf0763f91.png
43925448f9fa413a56b88afbf0763f91.png
43925448f9fa413a56b88afbf0763f91.png-620x348.png
43925448f9fa413a56b88afbf0763f91.png-620x348.png
9f0a7e6845698b779f6ab0e68960831e.png
9f0a7e6845698b779f6ab0e68960831e.png
9f0a7e6845698b779f6ab0e68960831e.png-620x348.png
9f0a7e6845698b779f6ab0e68960831e.png-620x348.png
DaveThib Reply
Mar 27, 2018 00:00

Hello AndreiSemkiv,

You actually have the answer in your screenshots. On this part, the master clock must be synchronous with the incoming LRCLK and BCLK signals. So either you will have to setup a master clock source and distribution to both parts or you must obtain the master clock from the PCM2706. I do not know that part to know if the master clock output will start up early and not stop. It needs to come up shortly after power-up and not go away.

Dave T

AndreiSemkiv Reply
Mar 28, 2018 00:00

Thank you, I think I understand. In any case, for processing the signal i2s from several sources, adau1452 + DAC is preferable. And synchronize the clock generators of these sources will not be necessary, with enough 3 signals: rlclk, bclk, data?

DaveThib Reply
Mar 28, 2018 00:00

Hello AndreiSemkiv,

Yes, the ADAU1452 is more flexible because it has built in ASRCs. So you can use them to take in data from other clock domains and you do not have to be locked to the same master clock. The 1701 does not have this capability.

Dave T

EZAdministrator Reply
Aug 2, 2018 00:00

This question has been assumed as answered either offline via email or with a multi-part answer. This question has now been closed out. If you have an inquiry related to this topic please post a new question in the applicable product forum.

Thank you,
EZ Admin