EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Measured Filter characteristic is half
I'm using ADAU1466, where is used coefficient calculations filter 2nd order. When I test output/input signal with frequency analyzer, I measure only half dumping, like is set in block. For example, wh
-
Strange standard RMS gain
I'm using ADAU1466, where is used Standard RMS block. Compressor is set 100:1, expander 1:1 . Signal to input is Sin 0dB, When I measure output to input, there is strange damping: Threeshold 0dB and m
-
I2S in/out salve mode
I’m trying to send and receive audio via I2S. AUDA1761 and CC2560 (BT chip from ti) are integrated into my circuit. In addition, I use two analog microphones and two analog speakers. The microphones a
-
ADAU1467 Self Boot Time
Hi, ADI Support Team I find the following description in Datasheet Page 28. ------------------------------- 3. If the SELFBOOT pin is pulled high, a self boot sequence initiates on the master control
-
ADAU1467 Datasheet Table52 Multipurpose Pins Registers
Hi, I'd like to know the correct address for ADAU1467 Datasheet Table52 Multipurpose Pins Registers. I found following description, are they correct? Furthermore, description of address after MP14_REA
-
Create compressor from basic dsp blocks
How can I create 1 channel compressor from basic dsp blocks? I'm using ADAU1466, Sigma Studio. There must be possibility to set over SPI only these parameters (not whole compressor curve): Threeshold
-
Phase consistency between 10 VCOs...
Hi guys! First post here for me. I'm an Italian ee that develops modular synthesizer modules (mainly analog... until now!) In the last two years I lurked EZ fascinated by the ADAU1701 and the marvels
-
Index Selectable Filters and probe/stim
I have an application where changing between 4 sets of IIR coefficients would be advantageous and found the index selectable filter. I loaded my 4 sets of coefficients and they save fine (there are th
-
ADAU1701 -- Output a copy of the I2S audio input to an I2S output
The context is: Custom board designed to be modular --- each particular board will use either L, or R, or possibly both, and may work with a particular audio band or with the full spectrum. Thus, I wa
-
FIR enable causing "Error Setting Control Value" window to pop up in SigmaStudio 4.2
I have a project with a few FIR filters in it, one of them is set to disabled. When I open the project in SigmaStudio 4.0 Build 2 rev 1759, things are ok. If I open it in SigmaStudio 4.2, a window pop
-
ADAU1450 Volume Control
I did a volume control test in the ADAU1450 and found no way to control the volume output (only no output and 3dB 2 results)
-
Sigma studio program protection.
Hi How do I protect the sigmastudio programed ADAU chips from reverse engineer by 3rd party? Thanks Tomdy eeprom sigmastudio
-
ADAU1467 DVDD regulator circuit
Hi, ADI support team I found the following description in the ADAU1452 datasheet. Is it applied to ADAU1467, too? -------------------------------------------------- If a ceramic 10 μF capacitor is
-
ADAU1467 Safeload for Double precision coefficient
Hi, ADI support team I know that the Safeload memory has 32 bit * 5 Data (data_safeLoad[0]-[5]). In case of Double precision, I believe that two Data is used for 1 coefficient. If I want to update fiv
-
Compressor selection
Hello. Can you help me, which block to use, or how to create compressor? I develop device for sound, now I'm using ADAU1466 development board, which is controlled over SPI with my base microprocessor.
-
[Bug Report] Export file contains addresses of second DSP
Title: Export file contains addresses of second DSP Description: The project contains two DSPs, ADAU1442 (IC1) and ADAU1452 (IC2). After a "Link Compile Download" and Export, the generated parameter X
-
ADAU1467 Is there any shut down sequence?
Hi, I'd like to know a requirement for shutdown sequence of ADAU1467. There is not specifically mentioned in the datasheet. Is there any problem even if shutting down without particular attention? Tha
-
ADAU1467 Please let me know the correct timing in the system initialization sequence.
Hi, I have a question about ADAU1467 system initialization sequence. I'd like to know the timing of the following two events in designing the system. 1. Time to start toggle from hardware reset releas
-
ADAU1467 How to setup in SDATAIOx as I2S.
Hello, I'd like to know how to set the SDATAIOx as I2S. The configuration GUI of SigmaStuio4.1's SDATAIOx seems to be unable to use these pins as I2S. Please let me know how to configure. Thanks and R
-
Is it possible to create a 800kHz square wave signal from MPx pin on ADAU1452?
Hi there, There is an application I need which is create a 800kHz square wave from MPx pin on ADAU1452. However, the seared wave source is 24kHz limited. Can I use frequency doubler or frequency multi
-
Weird ADZS-BF706 EZMINI output
Hi, I used other DSP product before, so I'm new to AD. I bought the ADZS-BF706-EZMINI from Mouser on November 2018, and I got some problem. I use CCES 2.81, Sigma Studio 4.2, and Talkthrough example f
-
ADAU1701 in self-boot mode --- mistake in my board design
Having made a mistake in my board design, I'd like to figure out whether I can (reasonably easily) get around it and make it work. As indicated in the subject, I'm using the ADAU1701 with an external
-
ADAU1701 TDM In - I2S out
Hello, in my current project I'm using an ADAU1701. On my system MCU I implemented an USB-to-TDM-Interface which delivers 8 channels with 24 bits at 48 kHz via TDM8. The Masterclock is 24.576 MHz, the
-
EVAL-ADAU1466Z schematic
Hello, I need information about the EVAL-ADAU1466Z. In this evaluation board schematic (UG-1135 rev. 0 available on the site) there are some port hanging. Two are OP_AMP_REF1 and OP_AMP_REF2 (pag. 33-
-
Limiter not working for 1777 project
Hello: When I use a standard limiter in a 1777 Eval project I get a System.NullReferenceException (see Fig. below for further details). When I replace the standard limiter with an external detect limi