EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1701 I2S issue with connecting master signals
I am trying to do something I thought to be simple, but something strange happens. In order to use ADAU1701 as a master: - Bridged MP10 to MP4 and MP 11 to MP5, short wire on the print. As soon as I c
-
Noise reduction algorithm module for Fs=48kHz
Sigma DSP has noise reduction algorithm module for ADAU1761. Unfortunately, it runs only for Fs=16kHz. What’s need to be done to run it for Fs=48kHz. Thanks Mark Audio Signal Processors noise reductio
-
SigmaStudio download link gone
I can't find the SigmaStudio download link on this page anymore: SigmaStudio | Analog Devices What is the location of the latest SigmaStudio download? Best regards, Daniel
-
Zero-cross "interpreter"
Hello, I am looking for a circuit that flips its output state from 0 to 1 (and vice versa) every second time a zero-cross on its input is detected. Please see enclosed graphics which shows what I mean
-
How to set BIAS DC on analog output for ADAU1442X evaluation board?
I have a Piezo-stack amplifier that needs a DC bias on the input sound signal. Input ranges 0-1V, 0-2.5V or 0-10V. Adding a DC to the sound signal in Sigmastudio only last for a short time (DC decay a
-
Problem using limiter in Sigma Studio after an FIR filter, as the Limiter gets frequency depenent.
Hi, I am having problems with a limiter if I use it after an FIR filter, as the limiter gets heavily frequency dependent. the maximum output level changes wildly with frequency despite being the last
-
ADAU1450 volume setting from microcontroller
Hello all, I could use your help with the following: We have an Adau1450 connected with I2C to a microcontroller. In the 1450 is a volume controller which I have to set with 8.24 fixedpoint values. Bu
-
How can I use extra auxiliary ADC by using an external mux to a ADAU1450?
Hi ADIs One of my customers is building an audio mixer with 16 knobs. She wants to receive 16 inputs from one ADC using an external MUX (16: 1). Do you have a reference to the Sigma Studio configurati
-
WRITEBACK in ADAU1452/67/63
How to do writeback in ADAU1452/67/63 chips? There is hint in http://www.analog.com/media/en/technical-documentation/user-guides/EVAL-ADAU1467Z-UG-1134.pdf But I am unclear how to configure the chip t
-
ADAU145x power down
Can we use the START_CORE register to enter a low power state with fast power up? Please advice how to enter power saving mode with fast recovery - with no re-booting? Audio Signal Processors adau1451
-
ADAU1452 RMS Compressor Coefficient Calculation
Hello, I am writing an app to control our DSP configuration on an ADAU1452. I have gotten to the point of controlling the RMS compressor but the GUI in relation to the coefficients seems incorrect. I
-
What are the system requirements for SS v3.16?
I'm running Windows 10 Enterprise and I'm not able to install v3.16. The installer chokes trying to install .NET 4.7. Is .NET 4.7 strictly necessary? It's a bit of a problem when an OS upgrade is requ
-
Impulse response table for FFT?
Hi: Playing with FFT--IFFT here... I want to multiply an impulse response with a music signal. The challenge is- there seems to be no way to 'load' an impulse response file into an FFT? In other words
-
Determine SPDIF input rate with ASRC ratio
Hi, I'm having a bit of confusion in a design using an ADAU1452. I have a 44.1k signal coming into the spdif input which is set to drive ASRC0. ASRC0 drives my core program (not important what that is
-
FxNLMS maximum number of taps for ADAU1452
Hi! I am working on an active noise cancellation project with the EVAL-ADAU1452MINIZ board and SigmaStudio ver. 3.15. The number of taps in SigmaStudio's FxNLMS adaptive filter seems to be limited to
-
SigmaStudio signal level detection, reduce trigger time
Hello, I found a signal level detection function in the following document site. https://wiki.analog.com/resources/tools-software/sigmastudio/toolbox/leveldetectorslookuptables/signaldetection However
-
Problem with "standard" stereo compressor circuit?
Been away from this forum for a while, but still having fun with SigmaDSPs :-) I have encountered a "gotcha" with this standard stereo compressor circuit as found in the AD Toolbox and elsewhere: To m
-
ADAU1466 'Paged' Address Mapping
Sigma Studio V 3.16 Build 4. Device ADAU1466 I've noticed that all addresses in the export files are expressed terms of Slave Port mapped addresses. There appears to be no indication in the various ex
-
Can I get board design database for the sigma DSP's EVAL B/D?
Hi all One of my customers wants design database for EVAL-ADAU1467Z. I searched for a design center, I found only some Blackfin's EVAL board data but no sigma DSP's EVAL board data. How can I find des
-
Filter calculation ADAU1466 192kHz
Hi, we encountered a problem with the calcuation of filter coefficients with the ADAU1466. With the ADAU1452 we convertet our values to fixedpoint with a constant 0x01000000 but this seems not to work
-
ADAU1701 /1401 Recommended Crystal Layout
Dear Analog, We have designed a system using the ADAU1701 and have experienced inconsistent communication to the unit over I2C and SPI. We have narrowed it down to the crystal oscillator being at faul
-
USBi firmware bug?
Hello, yesterday evening I investigated my massive problems with programming the selfboot EEPROM 25AA1024 on an ADAU1452 further and I think it is bug in the USBi firmware or in SigmaStudio. Therefore
-
Split one 32bit channel into two?
I've an idea and I'm looking for some quick feedback on how feasible it is on SigmaDSP. I would like to feed a 32 bit signal into an input port. The deceptive part of this is that this "channel" would
-
Migrating ADAU1452 to ADAU1466
Hello, I would like to replace ADAU1452 with ADAU1466 in an existing project. Hardware seems to be no problem (I built a prototype with ADAU1466 and it works with the old software) since these two are
-
ADAU1452 spi master port during reset?
Hi, what happens to the pins of the spi master port on an ADAU1452 when I set the device in reset? Are they going to high-z? In my target application I would like to program the eeprom by a microcontr