EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
echo cancellation
We’re currently using the Cirrus CS48LV12 (DSP) and CS42L73 (Codec). It appears that Cirrus isn’t interested in supporting the DSP/echo cancellation code, so I’m looking for an alternative. One option
-
What decimation ratio
Hello Guys, I am developing PDM MEMS mic with ADAU1451. We are using 48k UltraSound Mems. What is decimation ratio on ADAU1451 PDM Mic interface? Is it adjustable? Jason Audio Signal Processors adau14
-
ADAU1452 + AD1939 Solution - Need assistance please.
Hello, I am currently working on a solution with the ADAU1452 and the AD1939. The AD1939 is in SPI mode and connected to USBi, along with the ADAU1452. The USBi can read and write both devices success
-
URGENT: Forgot the thermal pad of ADAU1452. What now?
Hello, I just started to work on a PCB for the ADAU1452. However, I forgot to place the thermal pad on the footprint I created, so no electrical connection exists between the pad and the ground plane.
-
1452 FFT Capability
Basic Question: Does the 1452 series of DSPs have any useful FFT capability? As far as I can tell from these forums and in the software, the only thing you can do is add signals together. And unless I
-
ADAU 1450 I2S and GPIO output issues
Hello! I'm currently working on system based on ADAU1450, it's my own hardware design board. ADAU is working - I can communicate through SPI, write a program (using NumBytes and TxBuffer files generat
-
ADAU1701 looping timer circuit with a GPIO high @ every 10 sec.
Hi All, I have an ADAU1701 and need a GPIO pin to output high for +/- 1 sec. after every +/- 10 sec. The available timer isn't able to loop by itsself so I came up with the following schematic: When I
-
ADAU1701 Interface register read value incorrect
Hi Guys, I am planning to use 6 interface registers to store the ouput data of 6 RMS tables for an Arduino to read through I2C. When reading the data with the test setup shown below the data was shift
-
ADAU1701 how to use the data capture registers
Hi All, I have a few questions regarding the 2 byte Data Capture 0 and 1 registers at adress 1x081a and 0x081B. I can't seem to find alot of information about these registers at all. How much data can
-
One USBi, two 1701 with separate eeproms?
Looking for advise on feasibility of a system with a single USBi interface and two 1701 SigmaDSP's each with their own EEPROM for self boot. I would like to have the ability to have a single Sigma Stu
-
Dolby / DTS library in ADAU1772 / ADAU1777
Dear Sir, Our customer want to know whether ADAU1772 / ADAU1777 can support Dolby/DTS algorithm or not? If yes, what kind of algorithm can be supported? Our customer is more interesting in Dolby Surro
-
Karaoke key change using ADI pitch transposer alogrithm
Hi, I would like to implement the key change function for a karaoke machine using ADAU1451. I tried the ADI pitch transposer algorithm for the key change function. First, I don't know how to set the p
-
MLSSA file
The exmaple MLSSA file can not be found in SigmaStudio install directory. where could I found or someone can share to me(jh_leung@163.com)? thanks.
-
Best way to implement a dbu meter using 6 LED's
Hi All, I am trying to implement a dbu meter and have 6 LED's setup to do so... would like to do -24, -18, -12, -6, -3 and 0db light up accordingly. I have tried using the RMS limiter to do this and I
-
how to design my own PC software like sigma stdio use on ADSP21489?
Hello, I want to design my own PC software like sigmaStdio Used On ADSP21489 or other sharc processor,I have comprare with Biamp device,but we donot konw how to design?can we design pc software on sig
-
ADAU1701 evaluation board PCB
Dear Sir/Madam, We are developing a medical instrument using the evaluation board ADAU1701. It performs well. But we would like to design our own PCB. And I wonder whether you can share the layout of
-
DC Block component appears to introduce gain in ADAU1452
Hi, adding a DC Block component in the ADAU1452 appears to add 30dB of gain. To test this I simplified the signal path as far as possible. Output 0 produces the same level as applied to the input, whi
-
How to apply PEQ by using Safeload in ADAU1452
Hi All, I have a question for PEQ calculation in ADAU1452. Firstly I refered the below contents for Software Safeload and the PEQ calculation. - Software Safeload in ADAU1452 Datasheet . . - Write saf
-
Windows10 doesn't support sigmaStudio?
Because sigmaStudio must ust .netFramework 3.5. But in Windows10 cann't install .netFramework 3.5,so the sigmaStuido cann't use under windows 10. Is there any plan that ADI will port the software to W
-
Loudness block induces noise with ADAU1452 at 96kHz
Hi, I try to use the block "Loudness" but this one adds a distortion sound to the sound. Even at low volume. What do not I do well? Thank you for your help! Chris Audio Signal Processors adau1452 Sigm
-
ADAU1701 No sound (input problem)
I have just built a board with ADAU1701 dsp. If I program it to feed generated square wave to the outputs, I get it on my speakers. But when I'm using it to manipulate input signal I get no sound on t
-
ADAU1452 I2C Slave timing spec of tDH (data hold time)
Hi, Could you please reply to following questions ? a) ADAU1452 I2C Slave timing spec of tDH (data hold time) is 0.9 us (min) in datasheet, but is this correct ? We thought data hold time on standard
-
Guitar reverb and ADAU 1701
Hi There, I'm using a ADAU 1701 to create guitar effects in my new product. I have 3 sounds: Distortion, Chorus, and reverb. The Distortion and Chorus sound great, but I can't seem to get the Reverb t
-
ADAU1761 Inputs EMC Immunity
Hi. Does ADI have any specific recommendations or examples for filtering the electret microphone inputs of the ADAU1761 against incoming EMC? We are concerned about immunity issues, i.e. sensitivity t
-
adau1701 digital input
Hi. Can i with my ADAU1701 miniz Board handle 2 digital inputs (2 Stereo Channels)? On my Project we have 2 different soundmodules. The MCLK, BCLK, LRCLK is sync on all. I use the SDATA_IN for the fir