EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Add Control Signals for Parameters in Sigma DSP
I was wondering if there is a way to add controls to the parameters of the DSP modules in Sigma Studio. For example, I would like to have a signal control the length of a delay or the cutoff of a filt
-
Input block, 10 pins, ADAU1761?
Hello All, SigmaStudio is a fine development tool! The input block with its 10 pins is still a mystery for me. How do these connexions relate to the physical chip of an ADAU1761? Thanks for the commen
-
Bug Report: Pulse block, studio v3.13
ADAU1452 When compiling: ##### Compile Started: Tuesday, June 28, 2016 4:42:41 PM ##### error (16,Pulse1): offset value "139" out of range [-127, 127] in module PulseAlgS3001 (632,0) error (25,Pulse1)
-
EVAL-ADAU1452MINIZ no output on channels 2-7
I have a simple schematic executing on the EVAL-ADAU1452MINIZ that generates a sine wave and outputs it to a serial output channel to the AD1938. I can observe this sine wave when it's connected to ch
-
Change processor with redoing everything
How do I change the processor type from e.g. ADAU1452 to ADAU1451 without changing the register settings and the layout. Please answer fast because close to release day... Thanks. Audio Signal Process
-
Envelope Peak
Appreciate if somebody could explain the difference between “Envelope Peak” and “Envelope Peak Accurate”. Thank you envelope
-
Rise Time - Sample by Sample
Hello all, I would like to measure the rise time of an input signal using the ADAU 1452 but I'm not quite sure how to start. Basically, I would like to compare one sample to previous and next samples
-
ADAU1761 ADC noise floor
hi all, I am working with an ADAU1761. In the datasheet of the ADAU1761 it is mentioned that the ADC is 24-bit and that the noise level of the ADC is at least >98 dB. My question are: 1) are those 98
-
Post comment
I'm unable to post comments to a discussion that I started. Is the forum working correctly?
-
Adau1701 noise (tone) issues
Hi, I have made several prototype boards with the Adau1701 with external ADC/DAC solution (loudspeaker X-over). 1 thing that keeps giving issues, is (too much) noise and more specific a single tone (1
-
ADAU1701 compiler efficiency: 2nd order filter (grow)
HI All, Two issues: 1. Working with multichannel project on ADAU1701 I see that Biquad (2nd order filter, DP)(grow) uses the same (10) instructions as "2nd order filter" itself. Obviously no subroutin
-
Voice Activity Detector (VAD) block description
Hello All, We have a Analog Devices A2B bus evaluation kit which is based on ADAU1452 and as far as I understood features also one of these programmable audio dsps. Now we have realized a design with
-
Multiple sampling rates ADAU1452
Hello, finally got my ADAU1452 Board working. Based on the community help without any hastle. worked directly everything fine. Now a small questions regarding programming: I want to use a FIR filter a
-
Adaptive Beamformer in SigmaStudio
Hi, I am new in SigmaDSP. Now I am trying to use the adaptive beamformer in SigmaStudio based on the example provided by Adaptive Beam Forming [Analog Devices Wiki] The screenshot of the block diagram
-
[Bug Report] Scripting: Delay block - can't change MAX to larger value
The following script command will modify MAX delay samples value only if new value is lower than existing one: res = ss.ObjectSetProperties("setControlValue", delay_1_name, 0, 0, "DelaySamples`max", 2
-
Having troubles getting ADAU1452 to program ADAU1761 via I2C
ADAU1452 Slave Interface: - ADAU1452 I2C slave configuration and USBi interface seems to be working - Write Through DSP programming and verification function seems to work. - Is there an example proje
-
[ADAU1452] transmission distance
Hi, all I am wondering what is the transmission distance between 2-ADAU1452 Boards. (EVAL-ADAU1452) - Typ/Max/Min? Because, one of our customers asked us if it is possible to transmit at a distance of
-
SigmaStudio: is 88.2k sampling supported?
In Sigmastudio, in the drop down that lists the sampling frequencies, I see 48k, 96k and 192k but only 44100 and not 88.2k and 176.4k. Is it possible to develop a project with sampling rate set to 88.
-
Integration of EVAL-ADAU1X61EBZ with BeagleBone Black
Hello all, I am trying to integrate the EVAL-ADAU1X61EBZ evaluation board with BeagleBone Black. I tried installing the 1761 driver referring to the example code: linux/adi,adau17x1.txt at master · to
-
Moving between projects
Hi all, I'm a newbie for DSP development. I'd like to know if there is a document or notes about how to handle different kind of project. I mean: I'm developing (for 21489) both a schematic by SigmaSt
-
configuring the ADAU1962 to tdm8
Hi I am using the EZ board SC-584 with the Talkthrue code example. I have tried it out by inputting to the adau1979 with 4 inputs 2 SPORT channels (PRI+SEC) with stereo mode. and for output I use the
-
Cannot use filter beyond 30 kHz
Hi, I have a 33 kHz sinusoidal analog waveform with Vmin 0.5V and Vmax 2.5V. The frequency spectrum of this waveform also has minor amplitudes at frequencies higher and lower than 33 kHz that affect t
-
Will a CP2114 USB-to-I2S bridge chip work with the ADAU1701?
I'm trying to get a digital audio stream from a Windows PC into the ADAU1701 board. I'm trying to use a CP2114 USB-to-I2S bridge chip. I2S is being fed from the CP2114 into the I2S slave input on the
-
2x SigmaDSP controlled from single SigmaStudio
Hi Guys, Can I connect two SigmaDSPs to single SigmaStudio and work with both simultaneously?... My idea is to build a system with two SigmaDSP processors and control it using single SigmaStudio envir
-
Tracking low pass filter in sigma studio
Hello all, I'm trying to design a tracking low pass filter in sigma studio but can't seem to figure out how. Basically, I would like to use an RMS average value of the input signal to control the cut