EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU17001 Safeload and Level
Hello everyone, i am working with a ADAU1701 connected to a BeagleBoneBlack over spi , and after a lot of trial and error everything is working fine ! But i have two problems : 1.) When i execute the
-
Shrink or Consolidate Schematic Workspace
As my project has grown, particularly when I copy elements from one trial project or another into this project, the schematic workspace has become HUGE. (The up/down, left/right sliders have a long ra
-
Sigma Studio 3.12 .3 Beta (64bit) Operating System compatibility
Hello, I am using Sigma Studio 3.12.3 Beta (64bit) on my Windows 8 OS and encountered the following problem. each time i want to program and compile the eval board of ADAU1452, I need to create a new
-
Need help debugging proto board based on ADAV4601
Hello, I am having difficulty getting any sound from my ADAV4601 based proto board. Here is how it is put together: The crystal is 12.288MHz, not the default 24.576MHz There is WM8805 as SPDIF receive
-
Standard Independent RMS, but Mono?
Hi, I am building a typical mixer channel strip on an ADAU1442 and want to use the Standard Independent RMS Compressor. That's my choice because it seems to be the only one with the typical Attack, Re
-
ADAU145x I2C Master Port
Hello! I see in the ADAU145x there is a way to use the I2C control port to configure peripherals. i was wondering if it's possible to use the I2C port during operation as well. For example, i want to
-
ADAU1452 Eval board filters & output problems
Hi, I am new with this board and with DSP, so please forgive me if my questions sound stupid. I want to use this evaluation board as a crossover for experimentation. Specifically I'd like to feed the
-
An issue about ADAU1442
Dear Engineer, I am studying the part ADAU1442, and i plan to use I2C to control ADAU1442, changing the parameter (EQ, volume, route)at the same time. I wonder whether or not there are formula for vol
-
1701 Graphic EQ multiplex adc pins
Hi I'm wondering if there is an easy way to multiplex the analogue inputs on the 1701 so I could have say a 13 band graphic eq with external slider controls? Obviously a few bands is easy but I cannot
-
Noise that sometimes disappears on power off/on cycle
Hello, I'm getting some 40dB excess noise (hiss) on my ADAU1445 board which when turned off and on again several times, often disappears. With the USBi connected, much the same thing happens with hitt
-
ADAU1701 and I2C
If in the middle of downloading DSP program and parameters and the master clock goes away, what is the procedure to recover? Reset the DSP and start all over? If the I2C NAKs, can multiple retries be
-
State machine
Hello, I captured and pasted a state machine example from SigmaStudio Help. I would like to know what the units circled in red are. Best Regards, Mack
-
Sigmastudio limiter per frequency
Hi, I use ADAU1701 for a new application to drive a subwoofer. I'd like to add a limiter to protect against very low frequencies at high power. Usually, a high-pass filter is used for this purpose. Ho
-
Connect Raspberry Pi to ADAU1701 via I2S bus
Hi, I would like to connect the Raspberry Pi B+ or the Raspberry Pi 2 to the ADAU1701 via I2S bus. Searching on the web, I found some "guides" about this, but up to now I am not able to reproduce none
-
Why does ram read back as all zeros after writing to it?
I am finding that I can only read back zeros from the ADAU1442 rams after writing any data into them. I can read back registers in the E000 address space just fine but not the contents of the data, pr
-
ADAU1761 Power Consumption
I am trying to work out the power used by an ADAU1761. Referring to the data sheet http://www.analog.com/media/en/technical-documentation/data-sheets/ADAU1761.pdf pages 7, 8 and 9. I take a value from
-
SigmaStudio Limiter
Hi everyone, I use a board with ADAU1701 dsp. I plan for a new application using a Limiter. I setup a Limiter in a very basic project in SigmaStudio. I must be doing something very wrong as it will no
-
How does the resistor value at the MCLK input of ADAU1761affect the DSP core performance
Hi, Is there any resistor value limit at the MCLK input of ADAU1761? Why does the eval kit use 49.9ohms? Why can't use other value or is there any rational in between the RC value and master clock set
-
multirate process adau1451
hello everyone can someone explain how to use the new multirate feature in SigmaStudio 3.12 and adau1451, upsampling is possible? My project is running at fs48k, i need some process at 192kz , for exa
-
Start kit adau1701 vs 1761
I want to know what is better for learn dsp. The board 1701 or 1761.Because I m very confused with this issue.Can anybody help me. Regards. Audio Signal Processors SigmaDSP Audio Processors adau1701
-
Eval - ADAU1701MINIZ graph
Hi, I am using the graph component in the Eval-ADAU1701MINIZ I have an some issue 1. does the gain and phase graph takes in to consideration the cad delay(130us-1ms)? please explain to me best, Lobo
-
Does anybody have an example of how to use/read a SPST in order to handle a multiplexer in Sigma Studio?
Hello everybody, I am using the ADAU1701MINIZ with SigmaStudio, I have read the AN-951 regarding the use of hardware controls with GPIO pins, there are several example implementations of GPIO in softw
-
Sigma Studio Development Environment Stopped Working
I am using Windows 7 64-bit PC and installed SigmaStudio 3.7. When I try to open the existing *.dspproj project file, I get the error mentioned in the Subject. Windows tries to find a solution, but ne
-
Eval - ADAU1701MINIZ filter resolution
Hi, I have created a 3 stages filterilter MATLAB when I insert the parameters I get a different filter different filter I tried to verify with another board of cypress there the filter looks the same
-
sigma studio sub harmonic synth documentation missing
Hi I have tried using these blocks in an ADAU1701 without any apparent success, In desperation I went hunting for any documentation but there is NONE!! not even in https://wiki.analog.com/resources/to