EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Plotting filters frequency response
Hello, First, I'd like to apologize if this post isn't on the right section of the forum. Since we are using SigmaDSP on our product and I couldn't find a sub-forum that would fit this question best,
-
ADAU1772 Power Consumption
I have a question about the power consumption of ADAU1772. In page9 of the ADAU1772 data sheet, the power consumption when AVDD=IOVDD is 3.3V is described as 11.5mA. The measurement result of our boar
-
Signal detecting auto power on/off
Hi, I am thinking to design a auto power on/off when there is a presense/absense of audio input signal? Presense input signal : Power on Absense input signal (1 min) : Power off Can any of the GPIO of
-
RMS detection of 5 seconds of audio frames
Hi guys, I'm working on an ADAU1701 and I'd like to realize a RMS detector not just frame-by-frame, but taking into 5 seconds of audio data. I think that "watch block" can help me in order to manage t
-
adau1701 no i2c signal in selfboot
dear madam, sir, I'm new to this forum and I have a question. I've designed test board with the adau1701 dsp with the intention to use it in selfboot mode. I based this design on the selfboot design i
-
First value read by ADC can vary from chip to chip?
I'm reading an Aux ADC and then holding the minimum value with a slow release time. This has only been a problem on 1 out of 7 prototypes, but on that one, the value is held much lower than it should
-
ADAU1701
I want to know how to use the gpio pins to switch on and off the SB ? Audio Signal Processors SigmaDSP Audio Processors adau1701
-
Schematic/Gerber files for USBi communication board
Hi, Is it possible to share with me the schematic and gerber files for the USBi communication board which is used along with the EVALZ-ADAU1701MINI?
-
ADAU1701 Self Boot Programming.
So I want to use the ADAU1701 is self boot mode with external EEPROM. I have got Sigma Studio but I have no idea how to configure it to download the program without an USBi converter. Is it possible t
-
patch to fix sigma_tcp read failures
Hi, I had some issues using sigma_tcp on my arm based system running linux kernel 3.2; SigmaStudio kept reporting read errors. The attached patch fixed my issue; essentially on some systems ioctl can
-
Export Automatically?
I am doing some scripting for SigmaStudio 3.8, and I would love to be able to export (*.params, *.hex, ect.) files eaither through a script, automatically through a setting in SigmaStudio for everytim
-
Writeback with ADAU1442?
Is there any way to implement a writeback to EEPROM in ADAU1442 like there is in ADAU1701?
-
AD1940,ADAU1446 - Output noise
Sirs Testing the AD1940 and ADAU1446 Evaluations Boards, with a simple circuit (in directly to out), just using one channel (mono), I put a 1Khz sinus at input, and check the output test pin (with no
-
how to understand level detector value
Hello I want to show a animated volume bar. I set a level detector in my schematic. When I export project, I can get: Cell Name = MUSIC_VOL_L Parameter Name = SingleBandLevelDet1TCONST Parameter Addre
-
ADAU1701-MINIZ Communication failure
Hello, I have just received my evaluation board for ADAU1701 and been playing a few hours with it fine. However I had some minor trouble using it on different USB port but one was working fine so I de
-
SS 3.9!!!
Hurrah! Thanks you dear developers! I have just tried this version and finally could find the controlled sweep.Since it is still a beta version, I have a couple of questions, if you do not mind. 1. Is
-
ADAU1461 Botting
Dears can you give examples about micro-controllers that cheap and can boot ADAU1461 Regards
-
Question about Automatic Speaker EQ file format
Hi There! I am working with an ADAU1701 and am looking into the Automatic Speaker EQ block. The documentation says compatible formats include Impulse Responses with one measurement per line and Freque
-
Parameters To setValueControl
I have been trying to write a script in SigmaStudio to control the coefficients of a IIR Coefficient filter. For some reason, however, when I pass in the what seem to be correct parameters for the "se
-
AD1954 master/slave setting
Hi, I want to use the ADC->AD1954 to implement my project.I set the serial interface mode of the ADC to be master mode and I^2S.So I need to set the serial infterface mode of the AD1954 to be slave mo
-
ADAU1772 circuit diagram
I have a EVAL-ADAU1772Z. The layout of my board is different from figure described in UG-477. The revision number of my board is 110810_1 Rev B. I want the circuit diagram of this revision number. Can
-
MCLKI with I2S in ADAU1701
Hello, It's been discussed elsewhere but still want to confirm:Is it really required to synchronize MCLK with audio source when feeding I2S stream to ADAU1701 from I2S master? I2S stream gets synchron
-
build a hex file without hardware?
I made a 1772 design for a customer to evaluate on the EVM, and sent the EVM to them. Now I would like to update that design, generate a hex file and have them program the new code into the EVM for th
-
Between ADAU1761 and ADAU1781, are there any difference in serial data port ?
I have question about serial data port.Plese let me cofirm below. Are there any difference in serial data port between the ADAU1761 and the ADAU1781 ? When we use the ADAU1761's I2S in slave mode, is
-
Wiring - Multiple DSP boards
Dear Sirs I've started a project to process 8 in x 16 out audio mono channels. Drawing on Sigma, I've found that I need 5 DSP's to do it. So I need some help on wiring and choose some parts of IC's (4