EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1701 - Overvoltage Problem
Has anybody given too much supply voltage to the pins expecting 3.3v ? After testing my first printed PCB, I realized my 3.3 regulator was undersized for the current draw needed by the ADAU1701, and t
-
Is it possible to create an adaptive filter from discrete blocks in Sigma Studio?
I'm using the EVAL-ADAU170XEBZ evaluation board to try and produce an acoustic echo canceller for a project I am working on. I've read on the forums the existence of a Normalized Least Mean Squares(NL
-
EVAL-ADAU1442EBZ Op Amp circuits
I am following the schematics provided in the UG-032 datasheet for the eval-adau1442ebz to create our own board using the adau1442 (we also bought an eval-adau1442ebz for testing). My question is on t
-
Installing SigmaStudio on a networked PC
With some networks, the users' My Documents folder is mapped to a network drive for backup purposes. This is supposed to be transparent to each user, but it may cause your SigmaStudio installation to
-
How can I get a constant-dB envelope decay?
Hi, My current project calls for a Peak Programme Meter - a peak-reading level meter with fast attack, slow decay and a logarithmic scale. My system microcontroller reads the level value periodically
-
Is SigmaDSP memory volatile?
I am evaluating DSPs to use in a filtering project. I've read the datasheet for the ADAU1761 but don't see a clear answer to this: Are the program and coefficient RAM memories volatile or nonvolatile?
-
SigmaStudio not quite ready for prime time, is there something else?
Is SigmaStudio the only tool available for programming the ADAU1701 DSP, or can I use another development environment like VisualDSP or other from analog, or is there even a third party development en
-
Connecting SigmaStudio with TCP/IP
Hello, I’m working on a design containing a micro controller (with a Ethernet connection) and a ADAU1761. Testing is a bit difficult for me, I think because my I2C bus is used a lot. Maybe the USBi in
-
ADAU1761 noise removal algorithm
Hello, I has applied nosie reduction which is ADI's own algorithm on ADAU1761 for my application. From experiments, I verified that that algorithm is effetive in reduction of noise under 100Hz. Howeve
-
Taming sloppy schematics
As a project grows ad-hoc, it tends toward an unholy mess. It seems the sovereign remedy is to take a deep breath and redraw the project with the same stuff but this time with hindsight, following sta
-
1701 input overload protection?
Hi guyz! Just all of a sudden got this question. I am going to build a microphone pre-amplifier for 1701's analog inputs. So the maximum voltage level is 3.3v. The question is, whether the 1701 has an
-
ADAU1401 : 192KHz Sampling of S/PDIF from eval board: high freq distortion?
Hi, I'm trying to use the S/PDIF input and output on the ADAU1401A-EVAL board, running at a 192kHz Sample Rate. I've got the system working with slower sample rates (48, and 96 kHz specifically), howe
-
ADAU1772 noise cancelling application issue
Because the data sheet explain the ADAU1772 can use noise cancelling application and 15mw power consumption for typical noise cancelling solution. Could you tell me that the ADAU1772 have built in noi
-
ADAU1761 Self Boot-up Mode
Hi I am new to the Analog series of DSP and was attracted to the DSP's due to the fact that non-programmers such as myself could download Sigma Studio and compile programs without having to resort to
-
ADAU1701 12.288MHz clock don't always start=
Hi, I'm using a ADAU1701 with a 12.288MHz clock and sometimes it starts and other times it don't. I have a osc crystal with a 7pf shunt capacitance and using 22pf and 100 ohm resistor as the datasheet
-
Strange result from small addition to an existing project
Hi, My overall project has been though many revisions, growing to near the ADAU1701's capacity. After adding the two blocks circled below, instead of normal output the three used DACs all produce a sh
-
SigmaDSP(AD) miniDSP(TI)
Just wanted to ask people, who have dealt with them both, what are pros and cons of both? What are advantages and disadvantages of the one over the other one and vice versa? I am asking because at the
-
ADAU1701, Generic use of DVDD on application schematics
Hi, I'm using the ADAU1701 DSP with Sigma Studio IDE. I'm having issues with it working sometimes and then not. My question to start is pertaining the datasheet. It shows on the application schematic
-
How to output multiple I2S signal through ADAU1442 SPDIF out?
I have the I2S output from HDMI receiver ADV7612 as input to SigmaDSP ADAU1442, so I would like to convert/output these multiple I2S signals through SPDIF out. I've been looking for a block on Sigma S
-
Arbitrary Phase rotation from 0 to 180 degrees?
Hi There! How are you? I would like to provide an arbitrary phase rotation for the subwoofer outputs, so the user can use any phase angle from 0 to 180 degrees (let's say for example 60 degrees). I am
-
ADAU1442 channel assignment
Hi, the ADAU1442 is designed as a multi-stereo device by pairs of inputs and outputs and the datasheet documentation advises to use them as pairs. We would like to use the channel lines of the pairs t
-
Big problem when over 50% MIPS
Hi there, at the moment I am working on a fairly complex application where I use ADAU1442. 6 channels analog in (via ADC), 6 channels digital in (via AES/EBU-receiver + ASRC inside ADAU1442) and relat
-
Digital Lock-In amplifier implementation into stereo codec with DSP (like the ADAU 1761) ?
Dear All, I need to build an accurate sensor processing system for our laboratory and I consider to build an digital Lock - In amplifier based on DSP technology. I am new in the field of the DSP and b
-
Export maximum delay as a define when exporting system files
Hi everyone! Using SigmaStudio, I have managed to export my system parameters and configuration so I can change the parameters of the DSP with a microcontroller. The problem appears when I want to che
-
How to synchronize hierarchical boars?
Hi everyone, Let's suppose a scenario: I have a project with 6 hierarchical boards on it. All the 6 hierarchical boards are identical, and they have been added to the project using the "load board" me