EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1701 Communication Failure
Hello, I am completely new to dsp's and USBi so I am not entirely sure what is going wrong in my set up, but I get a communication failure when trying to program an adau1701. I am using an adau1701 mi
-
Real-time Tone Generation and Control with ADAU1761 and Microcontroller using SigmaDSP
Hello, I'm new to SigmaDSP and I'm working on a project with the ADAU1761 audio processor. My goal is to control this chip in real-time using a microcontroller. Specifically, I want to generate and co
-
Serial I2S and SPDIF TX not "in sync"
Hey forum, thanks for having me ! So in my ADAU1452 project I run the 4 I2S outputs pairs ( with 4 PCM5102 boards ) and the SPDIF TX ( with a SPDIF to ANALOG external DAC ) on the same 1khz internal s
-
Can somebody check if my program is OK?
Hello, Could somebody check if there is an error in my program? I'm new to Sigmastudio and don't what to look for at the moment. The first time I loaded this program into my tinysine board the speaker
-
Implementing Windowing for Constant Magnitude Output in Goertzel Algorithm on ADAU1761
Hello SigmaStudio community, I'm working on a Goertzel algorithm implementation for 500 Hz detection on the ADAU1761 using SigmaStudio. I've set up the basic algorithm, but I'm trying to achieve a con
-
Changing Q of State Variable also changes frequency.
Hi, I've started to use the State Variable (Q/F input) block and I'm observing that changing the Q also changes the frequency, please see pictures below that show this. Change Q to 10: Increasing the
-
dynamic bass
Is it possible to connect an external POT to control the dynamic bass block? I see examples where the block can be bypassed, but having the ability to control the boost with an external POT would be w
-
Equalizer
I want to make an equalizer with the ability to change parameters in real time, I use medium EQ, but when I boost certain frequencies, the level of the output signal increases, how can I equalize the
-
Multiple Band Level Detector Readback
I'm using a ADAU1701 to do some analysis on the frequency content of the ADC input then pull those readings into my MCU. I've had no problem performing a readback of a single level detector value, as
-
ReadBack Parameter Issue
Hello, I am trying to use "ReadBack Parameter" block in my ADAU1787 in order to obtain the FIR coefficients of a NLMS block. These coefficients will be used later on a FIR filter to compensate the sec
-
Load adau1761.bin in Linux but no reaction
Hello, I´ve a simple design on my evalboard and it runs. So i take it and create a adau1761.bin and copy it to the /lib/firmware folder on a customer hardware. In the log i can see, no error mes
-
Revision History / Summary of differences in these revisions
Dear Team, There are many revisions of EVAL-ADUSB2EBZ that were present , However, we see that there is no revision history that tells us about the differences in this board with every revision (for e
-
How do I modify this 2way project file to get the SPIDF output working on my HiFiBerry Beocreate 4ch amplifier?
I really need help on this or my boombox project is dead in the water! Here is a link to the 2-way project file I downloaded from HiFiBerry: https://www.hifiberry.com/wp-content/uploads/2017/10/2-way-
-
ADAU1467 TDM512 issues
Hello, I am using an AKM AK5538 ADC in TDM512 mode (schematic attached). The DSP settings for Serial In 0 are also attached. BCLKO0, LRCLK0 are outputs into the ADCs BCLK and LRCLK. MCLKO goes to ADC
-
Hands free device replacement with Sigma DSP?
Hello, I'm sourcing a technology replacement device for a Dual Echo Canceler & Noise Canceler with Dual Codec for Hands-Free device that went obsolete on one of our design. I'm looking for help in cho
-
Invalid Addition results with Signal Adder Module
Dear Team, We are using the ADAU1466 and Sigma Studio v4.5 . Our setup consists of two ADAU1466 Evaluation Boards wherein one is Master and the other is Slave. Below is the issue description I am atta
-
file download
hi. Can I have the programming file download. Thank you software
-
Auto EQ constantly tries to boost some frequencies even if it should not
Hello, I'm trying to use auto eq block to equalize the response of a speaker. I would like the filters to have only NEGATIVE boosts. As you can see in the image, I set the target curve to be a lot low
-
ADAU145x generating a reset signal for max hold when reading for example IPAT registers
Hello all, Does anyone know if it is possible to generate a reset signal for a "max and hold" block when reading from, for example, an IPAT register? I have five digital signals on MP inputs, which ca
-
ASRC Delay when adding Input Signals
Dear Team, I am using Sigma Studio v4.5 and ADAU1466 Evaluation Board. We have read the ASRC datasheet and from the datasheet it appears that the delay introduced by ASRC for 192Fs out 48 Fs In case i
-
Interface Read / Write ADAU1467
Hello together, we have a question about the Master Control Port Interface Read and Write. Our requirement is that we need to store some values, which are set during runtime of the ADAU1467, persisten
-
Analog ports not <orking anymore
Hello, I am using the ADAU1467 eval board to test the audio signals on a Bluetooth module. The setup is simple as shown in the following picture : I input the audio directly through the IN0 serial por
-
Weird output from delay block when delay is set to 0 samples
Hi! I'm having some problems with the simple delay block (not fractional) in SigmaStudio. When the delay is set to 0x00,0x00,0x00,0x00 (0 samples) it seems like the output is just garbage data from an
-
Time Constant Implementation
Hello, I have a question about time constant used in lockin amplifiers namely SRS Model SR865AM.( https://thinksrs.com/downloads/pdfs/manuals/SR865Am.pdf Page 62 Heading:Time Constants and Sensitivity
-
LRCLK_IN2
Dear all I use an ADAU1467 in combination with ESP32 via SPI. I use Serial Input Port 1 and Serial Input Port 2, both configured as masters. Serial Input Port 1 works perfectly. However, no LRCKL is g