EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1467 TDM8 SDATAIO configuration
Hello, I'm working on a project with double ADAU1467. The block diagram is the next: I have ADC1 and ADC2 connected in TDM8 mode to DSP0_SDATA_IN0 (4 channels each ADC), ADC3 connected in TDM8 mode (o
-
EVAL-ADAU1467Z / Windows Can't Detect USBi / MouserSO# 236070
Hi Tech Support, Good day. Need support on part# EVAL-ADAU1467Z. ( ADI D/C 2110 & Lot# 45829539 ) After installing all driver and software, they found windows can't detect his USBi interface board. LE
-
Inadvertent Value change on Hovering Mouse over Sigma Studio GUI
Dear Team, I am using Sigma Studio v4.5 and ADAU1466 Evaluation Board. It has come to our notice that the values in Sigma Studio GUI changes automatically while hovering the mouse over it . At times,
-
Sine wave Distortion at low amplitude levels
Dear Team , I was trying to capture a simple passthrough Sine wave Generator routed to SPDIF Output in ADAU1466. What I noticed was that Audio Distortion as shown below. I also recorded this in APx an
-
How to use multi adau1761 with axi i2s adi ip
I am using the ADAU1761 audio codec on my system with the Analog Devices AXI I2S ADI IP. I have successfully validated and run the system for one ADAU1761 using the following device tree on PetaLinux
-
add in XLR input
HI i built a stereo 2.1 speaker beginning of the year. It runs off the sure wondom jab5 amplifier with built-in adau1701 dsp. I currently have it running using just Bluetooth and it works perfectly we
-
How to use External SPI Delay Module on ADAU1452 with SigmaStudio Dev.Tool?
Hi, We want to use the External SPI Delay Module on ADAU1452 with SigmaStudio Dev.Tool.But I have some questions to ask for help. 1. Does the External SPI Delay Module work correctly in SigmaStudio De
-
Multirate Processing ASRC Signal Level Differences
Dear Team, We are using two Evaluation Boards ADAU1466 , one as ADAU1466 Master and the other as ADAU1466 Slave. Below is the overview of what we are trying to do : We wanted to know if the -2dB drop
-
ADAU146X - Low-Power Mode and Wake up from digital audio signal
Hello, I am trying to figure out a standby/sleep scheeme for a DSP/amplifier board featuring the ADAU1462/66. To wake up the board via my ADC its pretty clear, since it has a threshold based audio det
-
ADAU1467z Controlled via Bluetooth Module
Hello, A couple of months ago, I asked about making a Bluetooth-controlled digital equalizer for my university project. Based on the advice, I purchased an ADAU1467z. Although the project is still ong
-
How to script in SS+ EEPROM block read/write from Python
Creating some new Python scripts for SS+ that are similar to some ones done in SS 4.7. Now that SS+ has an EEPROM block I would like the script to be able read/write it as part of the test/production
-
POP noise observation in Analog output (Codec)
While interfacing 2 'EVAL-ADAU1452RevBZ' boards, pop noise is observed in Analog output. Please find the attached code package and analog output recorded waveform. We have doubted, this is due to cloc
-
resizing application window is difficult to impossible
Windows 10 22H2, 4k monitor. SS+ window can only be resized by grabbing in the corners, and it's very touchy as to where you have to position the cursor to get the grab handle (double arrow) to show.
-
fan control with autostart when audio signal is present
Good morning Guys, with ADAU1701 I want to implement heatsink fan control. So I used an ADC input for the two n.o. switch thermostats (I have two analogue thresholds 0V=over-temperature and 1.65V=high
-
SigmaStudio Tone control
Good morning, I really like the algorithm in the attached picture and I would like to be able to set it using external devices. Unfortunately, I noticed that when turning the treble/bass knobs, not on
-
How to use EEPROM block in SS+ for an I2C part?
I have a board with an ADAU1452 and an EEPROM that are controlled via I2C from a small micro. I would like to be able to load/read the EEPROM contents from SS+, which if you go to the settings looks p
-
Put a note on SS+ wiki page header or footer about how to search within the SS+ topic area.
Since local help and documentation has gone the way of the dodo bird, we're totally reliant on the wiki (and Dave's excellent videos...) It's not intuitively obvious how the SS+ wiki can be searched w
-
SPDIF Fs Support
Dear Team, Can anyone please confirm if the EVAL-AD2428WD1BZ Board's SPDIF supports 192kHz Fs or not . Regards, Zayn Audio Products hardware eval-ad2428wd1bz Automotive Audio Bus (A<sup>2</sup>B®) ad2
-
0dbfs input vs headroom used with LIMITER that allows +24db Threshol
Understanding that 0dbfs is full scale input from ADC or output to DAC, but that is based on the 24 bit audio signal. I know there is headroom within the DSP to allow for 42db of headroom according to
-
super bass alway make bass clip, how to control it?
final.dspproj I use the superbass function on the ADAU1401. I combined several mute ports to identify parts causing signal clipping. I ensured that the input and output gain on the ADAU1401 chip were
-
Split write register data
Hello, I'm trying to a split a write operation to a specific register that is suppose to receive 4880 bytes in multiple write operations of 256 bytes, and the DSP does not work properly after me doing
-
process structure in 1787 fast dsp FDSP
What is the process structure, with respect to number of bits in internal datapaths and memory and accumulator, used by the 1787 FDSP when executing a series of consecutive biquads? I imagine it is si
-
Change input/output signal by push button
Hi Everyone, Can use a push button that when pressed and released will change the input signal, and when pressed and held for about 3 seconds will change the output signal. Thank!! Audio Signal Proces
-
Use ADAU1797 on SigmaStudio+
Hello, I have started working with the ADAU1797 and am trying to configure SigmaStudio+ to use it. It says in the datasheet for the ADAU that it can be used on the software. However, once on the downl
-
AD1939 Sigma Studio Comms Failed
I've just built my first circuit/PCB with an AD1939 codec. Powered up and have checked for shorts in the circuit etc... Connected my USBi device (from an eval' board) and setup a quick SigmaStudio pro