EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Can the high-pass filter be set Butter/Link R/Bessel?
We use the ADAU1452 , and we need to develop the type of set high-pass filter, the range is None/Butter/Link R/Bessel. But we can't find these configuration items in the SigmaStudio Dev.tool's high-pa
-
Need to remove siren signal
I am working on a project that requires us to filter out siren noise. The frequencies of the sirens are 375 and 500 with the harmonic, 750, 1000, 1125, 1500 and so on. I was quite successful in filter
-
ADAU1452 + CODEC CS42448 is not working
I can not make the ADAU1452 with CS42448 working. I tried the small program provided bij ADI : RE: Using an external Audio Codec (cs42448) with ADAU1452 But it is not working. I dont know how to use t
-
Confusion About E2PROM and MCU
I'm trying to integrate the ADAU1702 into a project and I'm experiencing some confusion about how a permanently connected MCU and E2PROM are meant to interact, if at all. Do I need an E2PROM if I'm us
-
How to config ADAU1452 SDIN SOUT to use a same LRCLK and BCLK in sigma studio?
Hi Sir, In the project, The A2B(AD2428) give audio source( TMD8 ) to ADAU1452. I'd like to cope the received signal which is the A2B send to the A2B. Below the image is my setting,but is not work(Dout
-
ADAU1961- I2S testing options
Hi, We use the ADAU1961WBCPZ In the Jtag station we check the digital signal of our system. The Codec ADAU1961WBCPZ does not have Jtag lines. However we use to toggle the lines in Boundary scan and th
-
Signal peak limiter related to RMS level
Hi ADI Experts team, I need to know what blocks should be used to get the signal peaks limited by multiples of RMS signal. As example, using a factor related to RMS value to define the maximum peak va
-
Audio Level Controller in ADAU1772
ADAU1761 has "Automatic Level Control" (ALC) that controls the analog audio level. I am bound to use ADAU1772 with Zynq-7030 Board for my application requirements. How can I Control the Audio Level in
-
Which DSP board has the most spaces for potentiometers
Hallo everybody Which DSP board has the most spaces for potentiometers Audio Signal Processors adau1452 dsp potentiometer Audio Products hardware sigma SigmaDSP Audio Processors Show More
-
Simple Router
Dear all I expected that the only difference between "Simple Router" and "Simple Router with slew", is the slew. In real time capture I see that the controls are completely different to change input.
-
Adau1961 Laux and Raux pin question
For the Laux and Raux pins do they only bypass in one direction (from input to output) or is it bidirectional where you can take feedback and feed it to the adc (output to input)? Audio Products Integ
-
ADAU1452 - simple passthrough setup with ASRC
Hello everyone, I would like to create a very simple application on ADAU1452 that would take audio data on a serial input and passes them through to a serial output. As the sampling rate of input and
-
Balance/Fade capability
Hi, In hopes of using 4 speakers I have in my backyard via Bluetooth, I purchased the KABD4100 from Parts Express. Having 4 speakers I expected to be able to modify sound by bass/treble plus be able t
-
How to write volume value from spi-connected Arduino to safeload?
Hi. My problem is that I shut down the power using push volume on adau1466 When turned on, the volume is initialized (interface read, write does not work) So, by connecting Arduino Nano with SPI, I wa
-
Why does the dynamic range of digital input become smaller after DSP?
We use the ADAU1452, the digital audio input passes through the ADAU1452 and then the digital output, the dynamic range is 86dB. But the digital audio input skip the ADAU1452 to digital output, the dy
-
Wav Player
Dear all I use two WAV Player in my sketch. According to Wiki, the audio file must not exceed the size of the available DMO memory. Adau 1467 has 20,480 words (32 bits). Does this mean that 81,920 byt
-
[BUG REPORT]triangle oscillator (e.g.120Hz or 1200Hz) is not periodic
Triangle oscillator is sometimes not periodic even if the frequency is a divisor of the sample frequency (e.g.120Hz or 1200Hz at 48kHz) . Since 48000Hz/1200Hz is an integer, one would expect a perodic
-
ss4sh
Translation: Dear ADI technical support: I recently ran into a problem with SS4SH development and was hoping you could give me some answers. I'm using SC594 and ev-somcrr-ezkit for audio development,
-
ADAU1452 clock settings
Dear ADI Team, I'm just going through my first steps with ADAU1452. The example I would like to implement is simply a sine wave generator per this schematics: The desired sampling rate is 48 kHz and I
-
DC Offsets Through ASRCs
Hello, We've implemented a source select mechanism to switch between the three types of digital inputs on our amplifier design. We were noticing large, visible speaker excursions while performing swit
-
Adau 1701 TCPip dll protocol changed since Sigmastudio 4.5
Hi everybody, there has been a change in tcpip.dll since Sigmastudio 4.5. A simple read of two bytes that worked perfectly in 4.5 is no more working in 4.6 and 4.7. In sigmastudio 4.5 you can seee cle
-
ADAU1467 I2C parameter memory basic question
Ahoy there, I have a project that has a stereo mux in it, with three inputs, on my own board in selfboot mode. I have selfboot working fine, tested with a simple s/pdif through and a few controls. I w
-
ADAU1701 difficulty with index-selectable demux
Hi - As shown below, I'm attempting to use the index-selectable demux to bring either of two filters, or a white noise source, to a pair of outputs. I'd like a potentiometer on an auxiliary ADC to mak
-
Assistance and guidance on a DSP file for a portable speaker project
Hi Everyone, I'm working on a tuning setup for a small compact, battery powered Bluetooth speaker I am working on as a project, which utilises the ADAU1701JSTZ to tune sound of a 3 inch sub and two 1.
-
adau1701 clocks configurations
Hello dear engineers! I'm working on a project with ADAU1701, with an external main microcontroller that provides all the clocks to the DSP. I'm using TDM subordinate mode with a 1024 instructions len