EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1467 Eval Board I2C Programming
I'm working with the ADAU1467 Eval board, trying to set it up using a microcontroller through I2C. I've programmed it through Sigma Studio using I2C, and it works; sound starts playing through the spe
-
Sigma Studio ADAU1452 Algorithm Designer
Hi, I currently work with the ADAU1452 sigmaDSP and I want to write my own custom blocks with the Algorithm Designer available in the toolbox. I used this Algorithm designer module to write custom blo
-
Help with Modified FxLMS in an ANC application.
Hello and thank you for this forum. I am trying to implement ANC using the Modified FxLMS block. I have confirmed I have the microphones and speakers working. I have been able to run the training mode
-
HelpFiles for SigamStudio 4.7 missing
Trying to start help in SigmaStudio 4.7 does nothing .... Browsed to the helpfile dir C:\Program Files\Analog Devices\SigmaStudio 4.7\Help and it only contains a SigmaStudioHelp.chm of 89 kB, which is
-
ADAU1452 and PCM1802, Problems writing SPI EEPROM and no signal from ADC
Developing a ADAU1452 based board, using PCM1802 ADCs and PCM5102A DACs Have the board up and running. All PSU voltages within spec I can program it through I2C via Wondom ICP3 I can flip an GPIO pin
-
ADAU1761 RMS compressor table values
I have a GUI for a project using 3 ADAU1761. I would like to add custom/Realtime changes to the compressor curve. I can see the 34 table multipliers and how there are 3db steps and that flat is all 1'
-
Using I2S Audio Breakout as a subwoofer out (RCA) on ADAU1701 (KABD-430)
Hey guys, I’m working on a project where I’d like to include a subwoofer out to my KABD-430. It only has a I2S digital output available. I looked online and I couldn’t find much other than the SparkFu
-
ADAU1787 EVB I2S in & out non-reasonable
Hi ADI, I recently used ADAU1787 EVB and found some weird. When I ues I2S function which pin are SAI, I didn't give any input to AIN0 &1, even AIN0 &1+ tie to ground should have nothing at I2S ouput.
-
ADAU1962 XML project file
Hi teams Do you have a xml file for ADAU1962(EVALA-ADAU1966). I want to debug the evaluation board but I did not find the XML file. Audio Products software xml_files Audio D/A Converters adau1962
-
Eval-ADUSB2EBZ com problema
Good morning everybody My name is Valberto Aqui from Brazil. I purchased a DSP recorder, I used it only twice and it stopped working, that is, it no longer communicates with the PC, and it has a blue
-
Process each channel in a TDM4 input stream
Hi, I stream TDM4 signal to ADAU1452 sigmaDSP through SDATA_IN0. I want to process each channel from this TDM4 signal (Filter and maybe more). How can I do it? When done processing each channel, I nee
-
How to read certain address in ADAU1452 memory
Hi, I am trying to control the ADAU1452 dsp with ADI SC589 via i2c writings on A2B. I am able to write and read registers and memory of the adau1452. I want to read certain memory addresses in the ada
-
I2C Comms Failure ADAU1467
Attempting to configure ADAU1467 with SigmaStudio using I2C, getting "Comms Failure" result. Using SigmaStudio with SPI works fine, only I2C gets a comms failure result. I'm using Windows 10, Sigma St
-
Eval Board Repair/replace
I have two eval board that have issues. I asked my purchasing department to work with the distributor we bought them from to obtain replacements. That dragged on for months with no success so I asked
-
Instable S/PDIF output with the ADAU1463
Dear members, The problem encountered most probably is related to a similar problem encountered previously with the ADAU1452: ez.analog.com/.../instabel-88-khz-s-pdif-output-with-the-adau1452 I’m curr
-
adau1701 downsampling
How can I realize down sampling in ADAU1701, I know ADAU145X contains this module, we can use it directly. There is no this moudle in adau1701,so is there another way to get the same result? Audio Sig
-
ADAU1772 How to use analog input reference pins (AINxREF)
The ADAU1772 eval board schematic has AINxREF inputs tied to 10uF caps to ground. The datasheet, page 33, 2nd paragraph says these are biased at AVDD/2, and unused pins AC coupled to ground or tied to
-
AEC Trial Version
Hi, AEC trial version gets muted In 10 minutes during self-boot mode before 30 minutes (Documented). Audio Signal Processors software sigmaStudio 4.7 adau1467 sigma studio 4.7 SigmaDSP Audio Processor
-
Adaptive beamforming using ADAU1467z Eval Board and MIC-CANVAZ daughter board.
I was wondering if it would be possible to create a sigma studios project that is capable of adaptive beamforming using the ADAU1467Z eval board along with its MIC-CANVAZ daughter board using sigma st
-
Loudness vs Dynamic loudness
Hello, I'm just starting to learn DSP, I'm making a bluetooth speaker. Please help me understand the difference between Loudness and Dynamic loudness. In my understanding, Loudness itself dynamically
-
By detecting the gain of an input signal. Reduce the gain of another input signal
I want to use ADAU1452 to implement a function that inputs two audio signals (signal A and signal B) to detect the gain of signal A. When the gain of signal A is greater than -60dB (or other values),
-
Expander on FDSP of 1787, SigmaStudio
SigmaStudio lists an expander for the 1787 FDSP, but I cannot find any documentation on how it operates. I am specifically interested in the expander with external detect. I have played with various i
-
ADAU1772 functionality using external MCLK and i2S data
Here are use cases my manager asked about... We plan to run MCLK to all codecs (no local xtal or osc.) but it is undecided if it will be used - there is an unknown left that we need to understand. Is
-
Toggle ON/OFF cell turns OFF randomly - ADAU1701
Hi, I've been struggling with this problem for several days and I'm not getting to the bottom of it. In this simple block (part of a more complex project) I use the GPIO_6 input to control the toggle
-
ADAU1452 intermittently reporting strange panic codes
I have an ADAU1452 in a product that reports intermittent panic codes. This only happens at elevated temps (40C ambient) and about every 48 hours. The design is in production and this issue has only b