EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1401 very low signal to noise ratio
Hello, I have a noise problem with a development board that uses ADAU1401. It's made by a company called MIDIWORX and is almost identical to those mini dsp boards from china that cost about 20$. It lo
-
Remove audio feedback with ad1940(dsp)
Hi everyone It is currently designed with 4 microphone inputs and 2 line outputs. DSP CHIP AD1940 (4 mic inputs) + (1 line output feedback input) = 5 total. I'm testing with SIGMASTUDIO and it's not w
-
ADAU 1772 Cracking sound problem while i2c control
Dear All, I need your help on the below issue I have come across a strange problem and i need your help on this. I have a preliminary test board with ADAU 1772 with no self booting eeprom , and self b
-
AutoEQ empty when reopening
Hello, I am loving the AutoEQ function and it works fine. I export REW measurements as text, change the headline in the text file to be compatible with AutoEQ, import it under frequency response and c
-
PDM microphone clock frequency settings and left, right channels data
Hi Team, Two more questions on this subject. 1) PDM microphones that are connecting to the J2 LRCLK_IN2 and J2 BCLK_IN2 pins on the EVAL-ADAU1452 board. The PDM microphones have 2.4 MHz typical freque
-
mono signal input to EVAL-ADAU1787Z
Hi I evaluate EVAL-ADAU1787Z connecting to PC by USB. EVAL-ADAU1787Z outputs audio sound from J23(stereo output) successfully when stereo signal is input from J22(AIN2/AIN3) . But EVAL-ADAU1787Z does
-
One LEFT digital PDM microphone input but signal goes to both LEFT and RIGHT outputs
Hi Team, Please help. I am connecting only one digital PDM microphone to the LRCLK_IN2 and BCLK_IN2 on PDM channel 0 (with LR selection signal raised for LEFT side in my digital microphone) but the ou
-
Cannot get Safeload to work on ADAU1701
I can't get SafeLoad to work on 1701. i'm running an ESP32. I can write and read parameter memory, so I know my code is not complete garbage. :-) I just need to get rid of the pops! Is there an exampl
-
Two "Far End In" signals in AEC algorithms
Hi Team, Please help. I am using ADAU1452 and SigmaStudio v4.6 and I have two "Far End In" signals inputs that need to be go into AEC algorithm. Should I mix these two "Far End In" signals before Low
-
Cannot Get Shelf Filter to Match
Hi, I'm using ADAU1466 and cannot get my shelf filters to match my simulation tool. Simulation tool is VituixCad running generic (RBJ) DSP system at 48 kHz I have a 2nd order high shelf filter (12.920
-
External oscillator with ADAU1701 and multiple I2C codecs
Hey all, I'm new to the SigmaDSP platform and am currently working on several of my own designs using the ADAU1701 and ADAU1452. I also intend to use an external oscillator with at least the 1701 for
-
32 channel DAC @ 192kHz for testing: Recommendations?
For some experiments, we'd like a 32-channel DAC @ 192kHz. This is just for lab use so cost isn't a big factor. I was hoping to find some combination of eval boards to do this with relative ease. Ther
-
ADAU1701: Automatic analog input detection
Dear Team, Is there a way to automatically switch input channel to analog input when "line in" mini jack is connected? And then switch it back to i2s when analog input is disconnected? If so, what is
-
Miscellaneous Filter
Dear Team , I am using Sigma Studio v4.5 I am in the ADAU1452 Rev BZ processor. I am using the DC Blocking filter . Its cut off frequency is said to be 0.1 Hz? Is there a way to change it ? Also can I
-
Parameter Write Cell
Hi Team! I am currently using Sigma Studio 4.5 and cannot locate the Parameter Write block. The problem is with the Single Volume Control Sw Slew . I want to change its Slew mode and Slew rate The par
-
Compile error with "One Shot Rise" block on ADAU1467
Hello, Wanted to add "Table default value" after booting DSP. Found an example with "One Shot Rise" block on the forum. After adding block - "One Shot Rise" to my project it makes error during compila
-
EVAL_SSM2380Z Test Procedure Feb 2018.dspproj can not be open for testing purposes?
Good day !!! EVAL_SSM2380Z Test Procedure Feb 2018.dspproj can not be open for testing purposes?
-
DSP - ADAU1451 - State of pins during RESET
Hi, What is the state(Input or Output or High impedance) of the all the pins during RESET of DSP (ADAU1451). Audio Signal Processors adau1451 SigmaDSP Audio Processors
-
Obsolete algorithm replacement in adau1452 sigma studio v4.6 and Noise Reduction - 1452.dspprj downloaded sample project
Hi Team, In the "Compiler Output" there are some obsolete algorithms encountered, I have followed the instructions link. But still have which algorithm is used to replace the old one question. Please
-
Parameter Update cell in the Noise Reduction - 1452 .dspproj
Hi Team, This question is from "Noise Reduction - 1452.dspproj" that I have downloaded from ADI website. Please help with this "Disable Logic" Hierarchy Board" of how the "Parameter Update" cell can b
-
SigmaStudio v4.6 vs NoiseReductionTrial 1.0.0 vs FFT / IFFT vs AcousticEchoCancellationTrial on EVAL-ADAU1452
Hi Team, Please help. After managed install NoiseReductionTrial 1.0.0 block from "Available Downloads" category, the "Acoustic Echo Canceller" block appears in "ADI Algorithm" category, but there is N
-
Peak Compressor Unexpected Output
Dear Team, I am using the Peak( no gain ) N Channel Peak Compressor. I have the Compressor set as Limiter . Threshold : 0dB Ratio : Infinity. When i supply a 0dB sine wave as input to this module i re
-
Time from POWER_ENABLE0 to stabilization of SOP clock (BCLK / LRCLK) on ADAU1452
Hello, Please tell me the time from POWER_ENABLE0 to the stabilization of the SOP clock (BCLK / LRCLK) in ADAU1452. The SOP2 connection destination cannot be reset until the clock stabilizes. Communic
-
Momentary Button Sinus Push
I would need a method to connect a momentary button that plays a sine tone but never as long as the button is pressed and automatically stops again Audio Signal Processors button SigmaDSP Audio Proces
-
ADAU1467 no data signal on SDATA_OUT3
Hello All, I'm struggling to get a signal from the Serial Output Port 3 of the ADAU1467. BCLK and LRCK are present but no DATA... (pin60) I have verified the connections to the chip, checked my DAC on