EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
adau1701 ADC input hava white noise
I used 1.4112M the master clock frequency to adau1701, and white noise appeared in the simulated input without signal input. Audio Signal Processors SigmaDSP Audio Processors adau1701
-
SigmaStudio V3.14 Layout alignment ease
I have a fairly complex layout (lots of filters using all channels) and while I can use the Format->align * options, I'd like a bit more control. Is there a way I can force a specific spacing between
-
ADAU1466 self boot issue
Hi, I have read the forums and i cannot fathom why my 1466 eval board will not self boot. I have followed instructions to the letter. the best i can get is LED indication of LR clocks D3 D4 D5. But no
-
EVAL-ADAU1467 Data from ADC
Hello, is there any way to acquire the EVAL-ADAU1467 ADC data to a PC in parallel during it is also processed in the DSP? If yes, could you please advice what is needed? Many Thanks in advance! BR Eug
-
SigmaStudio EVAL-ADAU1787Z
Hi I just received EVAL-ADAU1787. Current SigmaStudio 4.2 has no ADAU1787 support. Could you please provide me SigmaStudio with ADAU1787 support that I can use EVAL-ADAU1787. Thank you in advance. ADA
-
Watchdog function of ADAU1467
Hi, I have a question about Watchdog function. I am refering the following description of ADAU1467 datasheet, but I could not understand the following description. "Using the largest prescale factor o
-
ADAU1467 Low-Shelf filter How to calculate filter coefficient
Hi, Please let me know how to calculate S(Large S) in the following formula. Thanks and Regards, Audio Signal Processors ADAU1467 SigmaStudio SigmaDSP adau1467 SigmaDSP Audio Processors
-
ADAU1467 How to determine safe load address (Page 1 or Page 2)
Hi, The ADAU1467 data sheet has the following description. Can I distinguish how the target cell is in Page1(lower memory) or in Page2(upper memory)? No such distinction is found in either the exporte
-
ADAU1701 with CS4272 96Khz, no luck
Hi there, I've had some difficulties trying to get a CS4272 codec working with the ADAU1701, CS4272 is configured as a standalone slave.I2S, Doublespeed mode for 96kHz. MCLK is provided by a buffered
-
ADAU1701 TAC
Hello Engineer Zone Community, Using the ADAU1701 we are in search of a recent application which should comprise a simple Time to Amplitude Conversion (TAC) within an audio processing circuitry. The T
-
No output From ADAU1701 to PCM5102 DAC on I2S when Programmer connected via I2C
I have a Sure DSP based ADAU1701 connected via I2S to a generic PCM5102A board, all works well until I connect the programmer board and then all output from the PCM1502 DAC stops, the ADAU1701 DACS ar
-
Can VC Delay be put in program memory?
In SS4.2 ADAU1452 there is a block called "Multi-Tap Voltage Controlled Delay". This block has 3 switches 0,1,PM. Does this mean you can put the delay in DM0, DM1 or in Program Memory? Unfortunately i
-
ADAU1761 Voice Compressor Example
Is there or could you provide an example for a great voice processor (dynamic voice processor). There are many choices in SigmaStudio but which combination gives a great result for voice recordings (e
-
Problems downloading program to ADAU1452
Hi, I am developing a DSP board with ADAU1452. The DSP is connected to an ESP32 though i2c. The connection seems to be fine. I am able to change filter parameters from the ESP32 though i2c (i2c slave
-
Field Upgrade of 1701 EEPROM without SigmaStudio
We have a mature product in the field that contains the 1701 that boots from EEPROM. We have since developed new features that numerous customers would like to take advantage of but I have no convenie
-
ADAU1467 Up Sampling module gives -6dB loss
Hi, The following Up Sampling converter is used to convert 48K source to 96K system. https://wiki.analog.com/resources/tools-software/sigmastudio/toolbox/multirateprocessing/upsampling The output of t
-
What's the use of SD card on EZ kit?
Hello everyone, Since the on chip memory is being used for Link-Compile-Download in sigma studio, I wanted to know the use of SD card on ez kit. Kindly reply. Thank you. adsp sc589 eval board ezkit fl
-
ADAU1467 Parametric EQ coefficient calculation
Hi The coefficient calculation method of the parametric EQ seems to be inconsistent with the data sent to the actual device. The above equation (1) makes the result be different. The above equation (2
-
ADAU1451 uses ADC to regulate EQ
Hello there, I am currently working on a 1451 solution that requires a potentiometer to adjust the EQ, input from the ADC port, treble and bass. I don't know which module to choose, Can you give me a
-
BF706 32 bit data to 24 bit ADAU1761 CODEC
Hi, I want to ask about the data precision. I used float data types before, however, the computational cost is too high that the cycle exceeds the limit. Thus, I tried to use a long fract data type (3
-
Detecting and processing command sequences in SigmaStudio
I'm using SigmaStudio and an ADAU1442 development board to process an audio input stream with 6 different channels, which I've been able to separate. One of these channels contains volume and mute inf
-
basic ADAU1452 / 1466 board help
Hello, I am pretty familiar now with the ADAU1701 and 176x series. I bought one of the many ADAU1452 boards on ebay produced by mediaworks.taobao.com. I expected to get a 1452 board but they ran out a
-
ADAU1466 external SPI Delay
I try to use higher external SPI delay in ADAU1466. When I use memory 23LC1024, it works well, delay is about 800ms in given channel for 96kHz. But I need more delay, that I try to use 4Mbit SRAM - IS
-
ADAU1467 Checksum result is different from expected value
Hi, Checksum result as shown followings, it is different expected and actual values. Is this phenomenon normal? Or does it contain any problems? Thanks and Regards, Audio Signal Processors adau1467 si
-
3 ADAU1761. sharing 12.288mhz clock. one of them runs at half frequency. An oscillator set to output 500hz outputs 250 hz.
3 ADAU1761. sharing 12.288mhz clock. one of them runs at half frequency. An oscillator set to output 500hz outputs 250 hz.. I discovered this problem after i added a test tone to my device. using 256*