EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Extending CPU capability of EVAL-ADAU144XEBZ
I need to have more CPU capacity on an EVAL-ADAU144XEBZ board. Is there a board with an ADAU 144X processor in the AD catalog which could be interfaced with the EVAL-ADAU144XEBZ ? I mean a board that
-
ADAU1467 To write data to any address of SigmaDSP from SigmaStudio GUI
Hi, I'd like to write data to any address of SigmaDSP from SigmaStudio GUI. The following modules (Register Read / Register Write/ DSP Parameter Read / Parameter Update) are in the ToolBox. Can they b
-
ADAU1467 Safeload Memory SPI access
Hi, The actual behavior of the device was observed when writing data to the safe load memory as follows. There are 2 questions. 1. During transmission, The SS signal once goes high, is it necessary on
-
ADAU1467 Initialization data different from the data sheet description
Hi, There are initialization data sent from SigmaStudio via SPI during SigmaDSP initialization. These data may differ from the descriptions in the data sheet documentation. Which should I adopt? Shoul
-
How to use 1452 or 1701 make a signal level detector to make LED has different brightness while signal strength change?
Hi, I want to use 1701 and 1452 to make a level detector to detect the signal strength, but I don't know how to use blocks to make led brightness will follow the signal strength. The led brightness le
-
ADAU1452 memory limit
Dear AD techs, i have a quite large project going on and i'm almost at the end of developing. Actually total PM used is around 7200 and i noticed that if i further add cells my program starts to have
-
adau1452 proper working on 192
have a custom board. crystal on 24 576. what proper settings for pll input output, pll,start clock requed? Audio Signal Processors adau1452 SigmaDSP Audio Processors
-
Assembler error. Index is out of range
I need help with next: eval-adau1466z board, testing delay. It works well. When I connect external SRAM memory to SPI, and use External SPI delay, System shows window in compilation: Assembler error I
-
SigmaStudio Peak Limiter calculations for use with host microcontroller
Where can I find calculations, equations, or methods for determining the run-time coefficients for the SigmaStudio Peak and RMS limiter DSP blocks? In the same manner that I have implemented filters a
-
Export the simulated response graph
I need to export the simulated response graph in Sigmastudio to an excel file. Is there a possibility to export the simulated response output to a csv or an excel file? This can give possibilities for
-
ADAU1452 Port Clock Speed Capability
Hi, In reference to the previous question as per the following link : https://ez.analog.com/dsp/sigmadsp/f/discussions/109083/adau1452-and-32bit-word-samples-with-filters-delay-and-volume-control---co
-
Input cap values on ADAU1701
Dear All, Can someone explain the function of the input capacitors on the ADC inputs for the ADAU1701. I'm new to electronics and I'm struggling to get hold of any 47uF capacitors at a reasonable pric
-
I2S Mixer
Hello, I want to mix 8 I2S iput signals in any combination at 10 I2S output signals. Is it possible with the ADAU1450? Audio Signal Processors adau1450 SigmaDSP Audio Processors
-
Sigmastudio adau1450 Dynamics compressor overlap filter
How can i know the overlap filter type? Audio Signal Processors adau1450 SigmaDSP Audio Processors
-
Different behaviour on ADAU1450 and ADAU1452 with external SPI delay
Hallo guys, we're developing an application based upon the ADAU1450 including the external SPI memory for additional delay (23LC1024-I). Although the same project works well on the ADAU1452, it doesn'
-
Connection external RAM to ADAU1466
Hello! I 'm interested of solution for this ask: https://ez.analog.com/dsp/sigmadsp/f/q-a/65791/about-external-delay-spi-ram-delay-in-adau1452 Where can I find function scheme of connecting external S
-
ADAU1452 Voltage Controlled SPI Delay issues?
Dear EZ, i've been using VC SPI delay cell in several projects but i always run into problems. Most of the time when this cell is used into a schematic and EEPROM is stored with data i have issues wit
-
Keep SigmaStudio module addresses the same after changes
Is there a way to keep module addresses the same as you work on a project? Every time I compile and link after adding a module the previously coded module addresses change. I guess the second question
-
MFXLMS for Active Noise Cancelling Documentation & Test Data
Hello, I was wondering if anyone has used the MFXLMS in Sigma Studio successfully. I have read over the documentation here: https://wiki.analog.com/resources/tools-software/sigmastudio/toolbox/filters
-
Automatic gain control using ADAU1701
We are going to implement the ADAU1701 within an industrial application which contains an audio processing. There is a need to configure an automatic gain control (AGC), but this DSP-type (ADAU1701) d
-
RS output is not stable when using ADI surround algorithm
We use ADI surround algorithm to transform 2ch input to 5 ch output on ADAU1450 which ran on EVAL-ADAU1452MINIZ. The following schematic is what we used: For ADI Surround algorithm, the parameter sett
-
Subharmonic Synth Plug-in with ADAU1467
Is this plug-in available for this DSP? Seems to show up in SigmaStudio on some chips but not this one but I would think it should be available for this chip. Using version 4.2 Audio Signal Processors
-
ADAU 1701 4 CHANNEL SSB TRANSRECIVER
Hello everyone, I have to implement a 4-channel SSB communication system with ADAU1701. I am obliged to use the 96.000 sample rate because otherwise I cannot make the modulation at 31.250 and at 32.76
-
ADAU1467 Sample Rate Converter (Synchronous SRC) generates an error.
Hi, The following design generates an error at compile time. This is a simple example using a SRC. I cannot found to avoid this error. Is there any way to avoid it. Is there any settings to be aware o
-
ADAU1442 EVM self-boot not working
Hi I have an EVAL-ADAU144XEB board. I use SigmaStudio 4.2 and USBi to communicate with the board and the board works fine, except that I cannot get self-boot working. When I reset the board, nothing h