EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1452 Custom Board Bringup Issue
I've been working on a custom ADAU1452 for an upcoming product prototype and the schematic for my breakout board seems correct, but all registers seem to read 0xFF / remote control via USBi is impossi
-
ADAU1701 Hard Clipper: Incomplete Peak Clipping
I am experiencing issues with the hard clipper in the ADAU1701, where it fails to clip all peaks above the threshold. This is my project. When the signal frequency is low, the clipper functions correc
-
safeload write for Mid Eq
Hello there, I'm testing the mid EQ filter in Sigmastudio, and got one question when safeloading the 5 coefficients into the ADAU1701, once i changed the boost value and updated, the 5 coefficients we
-
SafeLoad-sequence for 'Boost'-filter block.
We have a FDSP schematic designed w. "LarkStudio". A 'Boost' IIR 8-stage filter-block (peaking-filters) is used for audio equalizer functionality. To enable run-time setting of audio-band properties,
-
Filter Boost Gain is wrong
Dear Team, We are using the following Filter Module When using the Filter , we have observed that when setting the gain in the slider , there is always a -5dB difference from expected. Can you confirm
-
Amplitude Levels Differences at Higher Input Frequencies
Dear Team, We are using ADAU1466 in which we tried and setup a Passthrough code from SPDIF IN to SPDIF Out When we send an input signal at higher frequencies such as 13kHz we observe significant ampli
-
ADAU1467 ASRC Lock Bits
Hey together, I have a question regarding the ASRC Lock bits. I know that the lock bits are ACTIVE_LOW. Meaning 0x0000 would tell me everything is locked. So far this works as expected. But there is a
-
Product recommendation for 7band digital Parametric EQ Project.
Hello, I am a senior student in the Computer Engineering Department at University in Korea. I would like to inquire about purchasing products from Analog Devices. As part of our coursework, I am taske
-
ASRC RAMP MAX Override option in ADAU1466 Processor
Hi Team, I have a query in 'ASRC RAMPMAX OVR' Configuration enabling in ADAU1466 processor-based code. Please support. While 'ASRC RAMPMAX OVR' Configuration is enabled and value set as '-12', around
-
Much noise when connecting an I2C programmer to a ADAU1701 board .... what would be a general reason?
I have just made a new PCB with a ADAU1701, PCM1808 and 2 x PCM5102A I'm using Wondom ICP5 I2C programmer connected to RST, WP, SCL SDA and GND. When I connect the programmer to the board, I get quite
-
Wondom JAB 4 ADAU1701 DSP
Hello, I've been struggling with this for a bit and am trying to decide whether this is a software or hardware issue. I am using a WONDOM/Sure Electronics JAB 4 to power a desktop audio system. All fo
-
ParametricEQ frequency axis incorrect?
I am using ADAU1701 as a subwoofer active low pass filter and parametric EQ. While measuring the sub response and adjusting EQ, I noticed that frequencies appear to be incorrect in ParamEQ.For example
-
Microphone MI-3111 doesn't work
Hello, I have an adau1467 eval board. I connected my MI-3111 microphone and stereo output to the board and read the adau1467 user guide. But I want to get sound from the microphone and output from my
-
ADAU1452 SPDIF IN at 192Khz possible?
Hi, I am failing to receive SPDIF signal with sampling rate above 96kHz, is that possible with ADAU1452? Edit Notes . [edited by: zdr at 1:37 PM (GMT -4) on 29 Mar 2024] Audio Signal Processors adau14
-
i2s delay chain from input to output
Hi, in these days I'm testing the ADAU 1761 codec connected in I2S with an FPGA that generates the stimulus signals in order to check the behaviour of ADAU. The FPGA genearate a I2S toward the ADAU wo
-
Sending I2S from DSP to external DACs
Hi, I am trying to send I2S signal from DSP to external PCM1794 DACs. MCLK is sent out correctly from CLKOUT at 24.576MHz, but nothing else is getting out from serial outputs. What am I missing? Signa
-
Sigmastudio+ Real-time display capture rate
Ahoy there, I've just moved over to Sigmastudio+ from sigmastudio. Is there any way to increase the polling/read rate of the real-time display? As it stands it's far too slow to capture the sorts of t
-
Analog output observation with Serial Port 0 &1
Dear Team, We have the observation in Analog output of Serial Port1 is dependent with Serial Port0. Please find the below details. Sample project is attached. Please check is this expected. Serial Por
-
Serial Port Correct Settings
Dear Dave, Team, We are interfacing A2B with our ADAU1466 Evaluation Board . The flow is as follows A2B Main (running TDM16 @ 48kHz) -> A2B Sub Node(running TDM4 @ 192kHz {Increased Data Rate Feature)
-
SigmaStudio+
A delay of 500ms is required, divided into DM0 and DM1 blocks, but the total is still not more than 20480. But SigmaStudio software is OK. Audio Signal Processors adau1452 Audio Products software Sigm
-
DC value output
Dear Team , I am using the DC block from Sources in Sigma Studio v4.6.I am using the default Sigma Studio settings and with SPDIF Transmitter enabled. Now when I send a value AAAAAA to SPDIF and chcek
-
Pops when switching banks
Hi, I am currently working with ADAU 1787 fastDSP specifically with bank switching to change the gain in a smooth way. After trial and error, I have figured out that when switching banks, the Dynamic
-
First use of adau1452 - how to check basic operation
Hi Folks, I am trying to start newly soldered adau1452, but not sure if it's even working. USBi adapter is green and seems to be communicating, but eeprom read/writes fail, and seeing some conflicting
-
SigmaStudioPlus - how to export capture window to Excel?
I would like to export from the Capture window to Excel to make it more readable. All I get is all of the data in a single column vs. a row with all of the values comma or tab separated in a way that
-
SigmaStudioPlus buggy capture window - can't make Data field wider
In the capture window the data field only shows the first byte of multibyte data. Trying to make the field wider fails, it does some really weird stuff that I can only describe by showing this video: